Hi,Let's say we have an ASAv inserted on a Sevice graph in routed mode, currently allowing HTTP bettwen two EPGs App and Web. What changes i have to apply to add another protocol (HTTPS) between the two EPGs. Do i have to modify the existing contract...
Forum Posts
Resolved! VLAN to EPG to BD mapping
Hello, Trying to understand the best practice for VLAN to EPG to BD mapping and leaf connectivity. Let's say we have a number of virtual machines running on different VMware hosts all connected to the same leaf. These VMs belong to the same VLAN. The...
Can I use only 1 link of 1Giga and one device at each site, to buid a IPN network to connect 2 APIC ACI Multi Pod networks? I know that design guide show 4 devices and at least 2 10Giga link between PODs in a IPN. But, is that mandatory? Sample atta...
Resolved! WCCP Support in ACI
We have a requirement to configure ACI to support WCCP Web-Traffic needs to be sent to proxy server would like to know if WCCP is supported in ACI or not. Do We have to configure it under L4-L7. Could someone clarify. I had seen the https://community...
Resolved! Standby APIC in Multipod. Will work?
Recently I've found post about standby APIC in Multipod topology. Technology is based on using the same Node ID (2 for example) for fourth APIC at second pod, and keeping this node powered down and separated from fabric. Then during disaster recovery...
Resolved! App centric approach migration
Hello, Currently we have one xy application running in ACI as 'network centric mode'.SIngle-EPG=Single-BDEPG-50 (Six servers virtual machines)BD -50 ( 10.0.0.1) We are planing for app centric approach without changing application IP or subnet. App ...
Hi there, I installed the four acisim-3.2-1m_partX.OVA in ESXi, after that I received this message "Contact Cisco to supply response token for VM Activation challenge" and I need enter the activation token for continue with the installation (starting...
Hi, Im running APIC controller 3.0(2)K and I saw in previous versions that using "attach" to a Leaf, I can access the exec mode and input some shows. But in my version I go only to the "object" mode as bellow. apic1# bashadmin@apic1:~> attach Leaf01T...
Hello Experts. I have a pretty obscure issue with ACI L3out configuration. I have configured an OSPF on a routed interface and attached to the LEAF 101 inteface 1/1. I connected a Nexus switch to the interface 1/1. I can ping the interface IP ...
Hi, I have a requirement to establish the best path to upgrading a VSS pair of Catalyst 6500s in such a way that: We will reboot only one chassis and/or supervisor at a timeWe will maintain control over when and if the upgrade proceeds on the secon...
I've searched here and there and failed to find someone mentioned this - Maybe that indicates not possible. But I still wanna have a definite answer: assuming we have 3 VRF - A, B and C. Can we leak routes from VRF A to VRF B then leak those(or part...
I would like to upgrade a large amount of Cisco 2960 Catalyst Switches, I used APIC-EM to do the Plug n Play deployment. Is it possible to just do a IOS firmware upgrade on the switches using this solution after they have already been deployed? If so...
(performance is not an issue here) I was wondering how to use a VM inside of ACI as firewall for the north-south traffic for a specific tenant. I know how to integrate using a L3 Out with a physical firewall on the outside of ACI connected to ACI l...
Resolved! ACI deny rule for Specific endpoints
Hi folks,I have a /32 IPs configured in the ACL traditional switch within same subnet and different subnet as well.If i have to propose ACI solution and i need to restrict communication between Specific endpoints , which ACI solution I should use . C...
Hello.I am confused by the topology information that i deduce by issuing various show commands on various devices.For example, I know for sure that IP addr. 10.54.182.20 is within ACI environment because I do find this IP in EP tracker: By issuing #s...
