Hello, In an ongoing project our customer needs to integrate the DNA deployment with 2 separate ISE deployments : one is specific to the guest wireless use case. Is it possible to integrate DNA with two ISE deployments ? If so, how can we configure D...
Forum Posts
I am looking to implement a webhook notification for devices associated with our Cisco Spaces test building. When a device associates, I want to record the details.I am attempting to set up said webhook as exhibited here: Association (Northbound Noti...
Hello everyone,I'm setting up a RADSEC connection between our Cisco Catalyst 9800 WLC and a RadiusAAS service, but I'm hitting a "Certificate Unknown (46)" error during the handshake:On the Cisco side, the only error I’m seeing is: “RADSEC server ide...
We are looking at implementing a 1+1+1 DR solution. We have two Data Centers (DC01 and DC02) with layer 2 separation. We also have a Campus infrastructure attached to both DCs using layer 2.We have a single node cluster deployed in DC01 and we are go...
Hi, just wanted to check if this is correct? I ran it to template simulation editor and I didnt see any errors or any results...aaa authentication login default group tacacs+ local enabletacacs server CLEARPASSaddress ipv4 172.x.x.x#set($key= "\xxxxx...
DNAC Installed Version: 2.3.5.5-70026Cisco Catalyst 9800-80 17.9.4aAXE 9120i, 9130We have about 10 employees in our office using DNAC at varying role assignment levels.I am Super-Administrator and handle most of the the WIFI related tasks. Of all the...
When executing a Jija based template from DNAC/Catalyst Center on an ISR 1100 from factory defaults the following snippet is executed and fails to configure the embedded WLC. *Note this is a start to the config as the whole config still doesn't apply...
Resolved! Run Indicator Button in DNAc Applicance
hi all,i found below guide for indicator button in DNAc appliance.https://www.cisco.com/c/en/us/td/docs/cloud-systems-management/network-automation-and-management/dna-center/2-3-5/install_guide/2ndgen/b_cisco_dna_center_install_guide_2_3_5_2ndGen.pdf...
Hello, Could anyone please give me a rough idea of what is possible with Cisco Catalyst Centre regarding the Day 0 Install of 9200L Switches that will be stacked? What benefits can Catalyst Centre bring to the immediate install of the switches such a...
Hi,We recently rolled out our new SDA campus and had our Wireless in OTT due to using a single WLC for two different campuses. This was a temporary change and we are planning to roll our Wireless in SDA and separate admin domains for each WLC pair to...
Hi,I am trying to deploy tacacs authentication onto our cisco fleet of switches. I have followed the guide in Cisco DNA, I have created a template using this link 1. Create a Regular Template, then template editor and used velocity, then template sim...
Resolved! DNAC vulnerabilities
Hi All,I am running DNAC version 2.3.5.5 and currently below vulnerabilities have pop up after the scan has been run. Any recommendation how we can fix these.SSH Terrapin Prefix Truncation Weakness (CVE-2023-48795)SSH Server CBC Mode Ciphers Enabled
I am experiencing an issue related to the Cisco bug CSCup46714, where the logging source-interface command does not work as expected on my Cisco device. Device Model: C4500 connect in VSS. Current Firmware Version: 3.11.10 I would like to know if the...
Suggest me the alternate model for the Cisco Catalyst 9500 16-port 10G switch C9500-16X-E which supports virtual stacking with network modules.
Hello Team, I've been worried lately because I'm deploying a Cisco Catalyst 9407R 2 x C9400X-SUP-2XL supervisors. Everything is running fine, I haven't seen any warning in logs or leds, Everything is green. My worry is it because my monitor console ...
