I am running 2.3.5.6. I can't log into GUI with either Maglev or Admin profile. I have access to the CICM and SSH. Can anyone help me figure out what is going on?
Forum Posts
Resolved! Cisco DNAC / Catalyst Centre UPgrade
HI, new to DNAC / Catalyst Centre, I see that there is a release 2.3.7.6-70319 available to install.Having read through the release notes couple times, I feel I am missing something, can anyone kindly advise if this update is either critical or recom...
I have a number of switch listed in Failed section on the Catalyst Center plug and play page.Deleting them does nothing as they returns several minutes later.All of them are fully configured but still seem to think they are in plug and play mode.Does...
I'm standing up a new pair of C9800-40 WLCs using Catalyst Center. So far so good. It seems to add all the settings when I provision the 9800 through Catalyst Center.There's a few settings that I can't seem to find a way to include when the 9800 is p...
Hey all, I have exhausted my google searches. I am trying to manually add my WLC 5520 to my DNA Center deployment. This has proven to be quite challenging to say the least. I am at a point now to get the token and setup trustpoints from the DNAC ...
Hi, I have the responsibility of looking after a Cisco DNA / Cisco Catalyst Center box, there is an update, can you tell me if it possible to rollback to the current version if the upgrade fails ?Installed version:2.3.5.6-70143 - Release 2.3.7.6-703...
I have a single node Catalyst Center running 2.3.5.6 and two Cisco 5520 WLC running 8.10.190.0. I had to update the certificate on Catalyst Center as I was setting up pnp and had to update the cert SANs. The issue that I'm facing now is that I can't ...
Resolved! Can't factory reset Switch
Recently, the company I work for closed down a data center, and I ended up with a bunch of equipment, one of which is a C9300L-48P-4X-A - CISCO CATALYST 9300L 48P POE+ switch. It has some configuration on it, and I just want it to be a dumb switch wh...
Hi Just a question. What is checked if I do something like this in velocity. if ($interface.interfaceType == "Physical") because if I will call @$interface.portMode == "access" then I see that only interfeaces where switchport mode access is configur...
Hello everyone,I struggle with how to delete a file which I've uploaded to the namespace config, with the api call "POST /dna/intent/api/v1/file/{nameSpace}" in Cisco DNA Center.Thats the file I've uploaded, to use to configure a device via an api ca...
Hello,On C9300L switch , I have on every port soure Template and Network-Policy configured. The network policy is to tag the phone in Voice VLAN. After restarting the switch I get the following error for every Port:Command rejected: Network Policy Pr...
Hi, I've received two CW9162i in Cisco DNA management mode and would like to convert it to Meraki mode. I've checked the configuration guide and was only able to find a way through WLC or Catalyst 9300 switch which I don't have. https://www.cisco.co...
I am busy building/configuring a Cisco Catalyst Center (2.3.7.x). I configured the interfaces based on the configuration guide) as follows: Enterprise InterfaceIP4 Address: X.Y.5.146IP4 Netmask: 255.255.255.248Default Gateway IP4 Address:IP4 DNS Serv...
Resolved! Cisco (DNA) Spaces
I'm starting to play with Cisco Spaces, I won't hide the fact that I don't completely understand it yet. I've connected my WLC to Cisco Connector, and cisco Connector is connected to Cisco Spaces.I'm curious about a few things.1. I saw on one obsolet...
Version 2.3.5.6-70143Backups are failing with the following error in RED:```2024-09-12 03:31:53 4bb6b3ea-21b5-4240-8955-74521395c18f BACKUP.PREPARE_BACKUP SUCCESS2024-09-12 03:32:30 4bb6b3ea-21b5-4240-8955-74521395c18f BACKUP.maglev-system:credential...
