Hi,Here is the premiseLeaf 1 sends a route type 2 update with standard community to leaf 2 (border leaf) and then this /32 is redistributed into ipv4 vrf and advertised outside of EVPN fabric. The issue is with standard community, it's being stripped...
In a secure environment, no internet access from the switch, just for context. Also unable to copy/paste anything from that environment onto a machine with internet access. With that out of the way..NX-OS 9.3(7a)Every 2 hours, I am seeing this log en...
Hello everyone,Can someone please provide a list of Nexus switches that support ESI Multihoming (1&4 evpn routes) for LACP?We have 9318yc-fx and it's not supported on our platform.Thanks!
Hello,I have some nexus 93180lc-ex switches and while looking to upgrade to nxos 10 I found out that these switches are not supporting the 10.x version. Is there a specific reason not supporting this version? Hardware wise are the same with the 93180...
I have been working on an environment where a design was completed prior to my engagement. This is my first foray into configuring VXLAN but I have some experience with overlays/ACI/etc so am fairly comfortable. Design has 2x border leafs, 2x spines,...
There is a requirement to change admin password on various platforms in an organisation that I support. Basically, this is based on a Nexus 7k, 9k platforms. I know I use tcl scripting to configure this event, however I would like to know if there ar...
We have a Nexus switch - N9K-93180YC-FX - that is connected via 10G uplinks to multiple routers/switches, and it is connected to a certain router using a 1G interface.We need to limit the 1G interface usage for a certain subnet that traverses this 1G...
Hi,I have updated one Nexus 92348GC-X Switch to version 10.3.4a.I was hoping I can use the "configuration dual-stage" mode after the upgrade.But - when I type "configuration dual-stage" from execution mode, I getting this message -"command supported ...
Hi, I have a traffic analyzer service and I need to mirror a specific vlan's traffic to the interface that my analyzer is connected to.VXLAN-EVPN is employed in data center network.I have 4 leafs and the mentioned vlan exists on all leafs.Traffic ana...
I am planning to upgrade my C93180YC-FX3 switch from version 9.3.8 to 10.3.3. but during the upgrade process I get the message "Return code 0x40450037 (Not a valid nxos image)". I have confirmed that the nxos64-cs.10.3.3.F.bin file md5 is correct. At...
Can you provide what should be the normal temp sensor threshold for cisco nexus 9000 N9K-C983180YC-EX? Thank You. Is the sugarbowl CurrentTemp ok? because 58 degree celcius is equivalent to 136 degree farenheit Temperature:---------------------------...
Hi,There is a command "show tcp statistics" to get tcp statistics.whether this tcp statistics are of VSM or it includes tcp statistics of VSM+VMs on ESX.Thanks,D V
Hi,We are doing eap-tls 802.1x with Nexus 92348GC-X switch. But the switch disacrds the eap packets locally as soon as the client send the eap identity packet. The switch just acts locally - it just do not like the eap identity packet from client and...
Hello everyone,When you redistribute hmm into ipv4, these routes are advertised to other leaf switches, resulting in two routes installed in their respective ip-vrf. Something like this:BGP routing table entry for 192.168.10.11/32, version 6Paths: (2...
Hi, I have a vPC Border Leaf Switches that is connected to a pair of Firewall. Border Leaf-1 Eth1/1 <Po1> Firewall-1 Port1 Border Leaf-2 Eth1/1 <Po1> Firewall-1 Port2 Border Leaf-1 Eth1/2 <Po2> Firewall-2 Port1 Border Leaf-2 Eth1/2 <Po2> Firewall-2 P...
