I am trying to connect a Nexus C9216YC-X to a 2348TQ-E fex. The "install feature-set fex" is not an available command on the C9216YC-X.
Forum Posts
Hello, What is the length of Nexus 9508 AC power cable CAB-AC-16A-SG-IN? I couldn't find the dimensions in the installation guide. I suspect that it's 2.5m but I can't be sure. If possible please provide a photo/resource. Thank you! Lulu
Hello,I have a topology(attached) using 2x Cisco nexus 9396px switches in vpc mode. I enabled vxlan feature and I implement anycast vtep.The anycast IP is 192.168.93.93. The switchA has the 192.168.93.101 and the SwitchB the IP 192.168.93.102.Also, I...
Hello, A client of ours is building a new single VxLAN fabric based on Cisco N9K-C9332C, N9K-C93108TC-FX3P and N9K-C93108YC-FX3 using DCNM. What would be the recommended NX-OS release to run on these switches? Either 9.3.8, 10.1.2 or 10.2.1(F)? Thank...
I connected new two leafs 301,302 and configured vpc but when checking few commands like show vpc extended I can see consistency check not performed in one of the leaf (leaf 304) but not in leaf 303.i want to know why this error is appearing and how ...
Hello,We have a Nexus9000 C9396PX Chassis with a N9K-M4PC-CFP2 uplink board (4x100G CFP2). It used to work okay until we upgraded the NX-OS from 7 to 9. The current NX-OS version is 9.3.7 and now our transceiver details are being wrongly reported wit...
Does anyone know if Nexus N9K support Certifcate-based MACSec Encryption , esp one using Local Authentication (i.e w.o ISE or the like). Thanks
Do we need to configure NVE on Spine Switches or only on Leaf Switches?And if we can configure NVE interface on Spine switches , what is the need for that?
Dear all, I have a customer looking to refresh his network at two locations (say location A and B). We have proposed Cat 9500 at Core and Cat 9300 at the Distribution, for the two locations. They are also planning for Server Farm switches at the two ...
Hi, in a Cisco Nexus 2348TQ-E 10GE can i use one of the 6 QSFP+ 10/40 Gigabit Ethernet fabric interfaces as a normal uplink interface not connect to a parent switch?
Is Nexus 3K jumbo Frame required a switch reload? Default MTU is 1500 bytes. policy-map type network-qos jumboclass type network-qos class-defaultmtu 9216system qosservice-policy type network-qos jumbo
Hello Community, I have a question about OTV with HSRP, We have two DCs connected by OTV ( the underlay is VPLS ).We have only one OTV-edge in each DC ( OTV Unicast ), the purpose is to add second OTV edge in both DCs and make the HSRP redundancy. I ...
Good morning, I want to deploy the EVPN Multisite back-2-back and in design guide the minimum connectivity required is square but recommended full mesh between BGW located in different sites. What exactly will I lose if stay with square design becaus...
Hi there, I would like to ask about an issue I faced with ERSPAN. I configured span on N9K for traffic in/out to Nexus 3K which has a dual vpc link to the N9K. As soon as I configured it (see below config) the port-channel went down and lost connect...
I have a difficulty with the site interconnect Underlay portion of the config.. BGW 1 interface Ethernet1/53 description TO-SPINE1 ip address 10.0.1.1/30 ip router ospf UNDERLAY area 0.0.0.0 ip pim sparse-mode evpn multisite fabric-tracking interfa...
