My computer installed IE 11 last night and when I went to access the UCM webpage I couldn't access any of the drop down menus.Does anyone know of a work around other than uninstalling IE 11?
Hi All.I have a challenge deciciding which version of the Ciso Business Edition 6000 installation guide to use to prepare me for installing the device. The thing is I don't know which version the device will come in so I don't know which of the guide...
Hello everyone,I have been wondering if somebody knows the MTBF values for the following Cisco equipment:IP Phone 7821IP Phone CP6941UCS-SPV-C220-E ServerI couldn´t find these values in the datasheets of these devices.Thanks a lot.
HiI been experiencing multiple failures on Cisco 7941 and 7961 phones.When there is an incomming call and you lift the handset to answer, the phone continues to ring or transfers to speaker mode.I have rest the phone back to factory defaults, but th ...
Hello,Greetings to everyone. I'm having an issue with a new SIP Trunk to CUBE. What is happening the SP is only set to receive invites/etc from the class A address. Which is 4.35.201.X. Right now it is sending the inside address on the invite.INVITE ...
Hi FolksI had succesfully configured MVA on a lab environment with :- CUCM 9.1.1- H323 Gateway [Cisco 3925 - universal ios version 15.2(4)M5] with DID ISDN PRI- using direct MVAI'm able to reach the IVR menu and authenticate PIN number.Then I select ...
DEARi am experiecing problem on cisco unity. i have a doubt but not sure. I was configuring call management - Auto Attendant. I didn't make any big changed i just created one handler thats it and deleted later. After that i am not getting voice mail ...
I have my CME that is in 3945 Router, when i register Ip phone some of 7931 registered and working but some after reseting them they stop in upgrading state.
I am trying to understand how FXO ports work. I have little experience with this so I am trying to learn how it works at our office. We have a Cisco 2801 with CME 8.1 and CUE 3.2. The 2801 has a VIC2-4FXO card in it. It has 3 analog phone lines a...
Hi, I try to install cuc 7.0(2) at vCloud but it always getting error "/usr/local/bin/base_scripts/sd_ifconfig -eth0 -ethtool "autoneg on" ... failed with return code 256" I check NIC already add but not connect to network due internal issue?Is it th...
We have a 2801 router with CME 8.1 and CUE 3.2.3. We receive calls on 3 analog lines into a 4 port FXO card. When calls arrive they reach an Automated Attendant which routes the calls properly. The issue we encounter is that the analog lines do no...
hi everyone,so if ephone registers with cme and get a number with auto assign configured, so does the router save the association of the Mac address and the dn to startup configuration so that particular phone will always be assigned that dn after th...
I purchased the internal use (NFR) package for internal training / learning...The paskage was delivered as a series of ISO files.. The naming of each of them needed a translator...After figuring out which ISO was the call manager ISO, I created a VM...
I have just installed Cisco Presence server 8.5.1, CUCM 8.5.1 integrated with LDAP. I also have Cisco Unified Personal Communicator 8.5.3 installed on my laptop for testing. CUPC is also integrated with LDAP. I have followed the documents and finishe...
Hi all memebers I would have to ask a question about the switch spec i need.we have a hotel (12 floor each floor 26 ip telephony and 6 access point so i don't think the end user really need file exchanges in the network).my plans is to use 48 port...
