Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,In my CME 7.1 version, i have to configure the CP-3905, but if i list the possible models, just show 3911 and 3951 , how can i have load the CP-3905?Follow:ROUTER_VOIP(config-register-global)#load ? 3911 Select the firmware load file for 3...
Hi,My customer is migrating is ToIP infrastructure from traditionnal gateway with E1s to a SIP Trunk.I have to implement the design below :VG224 <---sccp---> CUCM 6.1.4 <---sip trunk----> ProviderandSagemXmediusFaxServer <---H323---> CUCM 6.1.4 <---s...
Hi,Is it possible to transcode NSE based T.38 to protocol based T.38 whit a CUBE ?I would like to have NSE based T.38 between CUCM6.1 and CUBE. And protocol based T.38 between CUBE and my SIP trunk provider.If this is possible, can I do it in softwar...
We recently replaced a dead ATA 186 with a 187. Since that time the caller on the analog side is noticing static on their side and the other caller is hearing echo. We have tried changing pairs between the ATA 187 and the analog phone, but the issu...
All.I just recently performed an upgrade test in a lab. In this scenario I needed to change the IP addresses and host names of the Communications Manager. I performed a back and restore and then upgraded that restore in a virtual machine. I only r...
Dear NetPro gurus,My client just installed a brand new CME with CUE on a Cisco 3945 ISR G2 router. However, they have over 30 Analogue phones which are connected to 2 x Cisco VG224, which in turn is registered with CME.They have the following enquir...
Hi Please, share anyway to add a user role to have permission to configure specific group of DNs or group of IP Phones? Such as, user A has the permission to configure DN 1500-1505.B.R.Winai
hi,I make an video call from a CIsco IP 9971 to an Cisco Cius. Call established, both can speak an hear. At the 9971 I can see the video, at the Cius the video is shortly appearing and the going down. At display message appears like this: "phone proc...
ITSP--------CCME----------CUEdial-peer confg:dial-peer voice 10 voipincoming called number.dtmf relay rtp-nte codec g711udial-peer voice 11 voipdestination-pattern 444description to CUE AAsession target ipv4: XXXXdtmf-relay sip-notify The i...
Hi all, today one of our site in South Korea reports that they can not hear the voice when pickup call from ISDN, both incoming and outgoing are same issue. system was runnig without problem for months and there is no any change on...
Hi,when we make out going calls, i want to select second line by default. plz suggest me where i s the settings to be changed in call manager.Regards,Baskaran.M
Hi there,Don’t think this is possible but though I would double check. There is a requirement for a broadcast hunt group to be setup with some of the users registered on different clusters. CM version is 8.5 and cluster are connected via SIP trunk.Is...
Dear Community, I have been requested to explore the possibility of using G.726 codec within and between regions on Corporate Telephony System that involves CUCM8.5, CUCM6.1 and a couple of Call Manager Express. I was wondering if g726 is available o...
Hi,I have problem with fax configuration usig SIP trunk connection. I'll explani step by step my problem below.I have CCM 8.6 with gateways C3925 (SIP is terminated there also have analog ports for fax) and VG224 (for analog fax machines).At first I ...
Dear all, We are facing a problem with incoming calls received via FCTs connected to our CME by FXO ports. Outgoing calls through the FCTs are working fine and the cell called is seeing the right cell number as caller ID.The problem raises when we ca...
