Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Currently have a Unity Connect set up in a failover configration at two diffrent datacenters. UCM is also located at multiple locations, cluster includes 4 subs. My goal is to make sure that the primary UC appliance registers to the Sub located in t...
I am placing upgrade order through UCSS (CUWL workspace License).It is CUCM upgrade from 7.x to 8.x for THREE Nodes (One Pub and Two Sub)Question is: For Upgrade media kit and Three Node licenses, below upgrade Part# are correct?Do I need both Part# ...
Hello,I’m working for one Voice project and would like to ask some technical questions. Please kindly advice if you have any ideas.We have two offices, A and B.A is like a HQ and using CUCM 8 with ISDN 10.B is a branch office and they are using norma...
Hi,I have a CME. After making a restar under telephony-service, the phones remain in deceased state:ephone-31[30] Mac:D0D0.FD71.181B TCP socket:[-1] activeLine:0 whisperLine:0 DECEASEDephone-37[36] Mac:D0D0.FD71.1834 TCP socket:[-1] activeLine:0 whi...
I am working an issue for Intermittent calls dropping, returning fast busy.Here is the output of the RTMT log for the issue we see.10/28/2010 15:37:51.546 CCM|Digit analysis: match(pi="2", fqcn="5133866428", cn="6428",plv="5", pss="BlockExploitPSTN_P...
Is there any way to prevent an FXO port from picking up the call immediately on incoming calls?By this I mean that CME picks up the FXO port then generates its own ringback tone for the caller. Most other PBX systems in my experience seem to not actu...
I have a meet me conf bridge numbers that have worked in the past but now when you press the meet me button on the 7936 phone you are not prompted with a tone to enter the number. I have used my IP Communicator and pressed the meet me button entered ...
Hi,Can i install IPCC Express on a MCS-7835-RC1/RC2 server? Any quick help would be realy apprciatedThanx in AdvanceMadan
All,I have a CME dployed at one of teh sites for one of our clients. There are only 15 phones in total but 3 among them suddenly got unregistered. I have no idea as to what happened. I would like to be advised of a few trubleshooting steps and I ahve...
All calls from PSTN displayed as Unknown number .what steps should i take to troubleshoot this issue ?
Hello all,I'm having some difficulties trying to get incoming calls from a Microsoft Lync 2010 server to work. I have two of somewhat the same environments, one at home (for testing purposes) and one at work. These environments are not exactly the sa...
Good day!!!Does anyone have working configuration of Nokia E71 with Nokia Call Connect 1.1 integrated to CCME 7.1?As I've understood CUCME is supported with Nokia Call Connect 1.1 only.Regards,Pavel
Hello,we ordered several additional Cisco ATA 186 for our Customer, but we received the new ones (ATA 187).now i have problems with the callerid. no matter what i configure unter the Caller id Configuration (CUCM 8.0(3)) my phone does not display any...
Hi All, My CUCM version is "Version: 6.0.1.2000-3". And I am trying to install a device pack (version: cmterm-devicepack6.0.1.3129-1.cop.sgn) for supporting phone 7965. I trying installing by remote option usinf sftp. Everything is fine upto downla...
I have a UC 520 and after 4 rings then the aa is picked up when the pilot is rang. Any idea why this is happening and how this seconds can be reduced to one ring for the most?
