MPLS

Our configurations require an outbound route-map from the PE to the route reflector to set some attributes (such as local preference or community). In the route-map configuration we have: route-map send-to-rr permit 10 match ip address prefix-list h...

Hi,I have a PE router running MPBGP which receives two default routes to the internet through an IPV4 BGP session. I need to import these routes in to a VRF and export them to different customer VRFs so that these VRFs are able to access Internet.I h...

Hi,I have a core routers which are mpls as well as ipv6 enabled . Now I want to give ipv6 vpn service to the customer.Is that possible ? any document on that will be appreciated.I have read the 6pe feature but that is talking about giving ipv6 servic...

Hi,We have a need to provide "GOLD" priority to a clients ethernet connections between our POPS(I have attached config that will hopefully achieve this over 2 PE's) - The client is also requesting that Citrix traffic be given the highest priority als...

l'm working on a 12410, i have a SIP 501, i want to confirm that the SIP is working correctly.tha status and Rate LED of the SIP 501 remain Yellow, and when starting uo the Card, il receive an error Message :GRPSPA-3-ERROR: slot 7: null TSM proc data...

Hello,I have a question regarding the redistribution process in MPLS network on the SAME PE router.I have PE-CE RIPv2, and in the MPLS is MP-BGPv4. Between MPLS Core and LAN Core is OSPF.I redistribute RIP to BGP on PE, so I have CE routes in the BGP...

Attempted to apply service-policy output MPLS-EGRESS to ATM Int:!class-map match-any GOLD match mpls experimental topmost 5 match ip precedence 5 class-map match-any BRONZE match mpls experimental topmost 3 match ip precedence 3 class-map match-any...

Hi, 1)I heard that control word is not mandatory in ethernet attached circuits in a VPWS ? Can anyone let me know the reason ? 2) Is there any equivalent concept of control word in IP pseudowire (eg.in the case of Kompella circuits , ATM on one side...

Hi,I have two questions:1. Can anyone put in plain words the differences between E-LSP and L-LSP and what would be a valid application of each?2. Is it correct that when poping labels the EXP value is not copied to a revealed label by default (as opp...

If anyone has sucessfully configured inter-as multicast VPN. Can you please provide sample config. I am trying to get multicast VPN working in the scenerio below. ------AS#100------------AS#200---------vpna-PE1-ASBR(RR)-----ASBR(RR)-PE1-vpna

Hi,My organization has a network with many remote sites connected through Layer-2 MPLS.The hub site is a Cisco 6500 and the remote sites are 3550 switches. The MPLS links to the remote sites are of 10Mbps. There is no configuration w.r.t MPLS on the ...

hy guys,i want to upgrade a cisco 12406 from IOS to IOS XR . there is someone who did already this ?System image file is "disk0:c12kprp-p-mz.120-32.S3.bin"GSR_12406#sh gsrSlot 0 type = Performance Route Processor state = ACTV RP IOS Runnin...

I have a situation whereby any subnet that is advertised by MPLS becomes immediately unreachable. One of the routers that is meant to forward the data has VLAN enabled on the MPLS interface the traffic is then untagged by our provider before it is fo...

I have a EBGP-peering connecting two AS with both address-family ipv4 and ipv6 but the prefixes advertized from each AS does get dropped by the other end of the session by local policy:"MP_REACH NEXT_HOP Martian: n/a 2239"The ...