Network Management

Hi,We just installed new Ciscoworks LMS 3.2, and sent all switches syslog message to this Ciscoworks LMS 3.2 and old Ciscoworks LMS 2.5 server.Old Ciscowork LMS 2.5 server can receive syslog message and syslog appear at old LMS 2.5 syslog report, but...

We are in the process of replacing our core routers with 2 pairs of Nexus 7010 (running version 4.2.3) devices, that have been running in parallel to the existing infrastructure for a while.While looking in CiscoWorks LMS user tracking, we see end ho...

I'm not confident our ASA is configured to send SNMP TRAPS. It appears to only be sending 'traps' via SYSLOG formats. I think there are two choices during configuration or will both (syslog format and mib-trap format) worth independently? Is there an...

Hello,Cant update packages via psu (GUI&CLI), because there should be a 2nd psu process running and that because a lockfile should be open.But there isnt:D:\CSCOpx>dir /S Psu.Lock Volume in drive D is Ciscoworks Volume Serial Number is 9046-C1CCFile ...

Hi all,I've got the following error in Inventory Collection: 'RICS0001:Internal Error,unable to process the collected data from the device.'System is CW LMS 2.6If I search the web I get the following Cisco document:http://www.cisco.com/en/US/products...

Hello everyone,I am trying to reduce the amount of syslog messages. Can anyone tell me the lowest level of notifications I can set that will give me an alert if an Interface goes down?Thakns in advance!

Windows Server 2008 Standard LMS 3.2 with RME 4.3.1 When I try to select devices to check/compare device configurations in the RME Archive Mgmt menu (RME -> Archive Mgmt -> Compare Configs) no device shows up for me to select. I know the configurat...

Hi all,         Any one help me to configure router and switch log on windows server. I dont have any idea please send me link or guide to configure syslog server on windows.  For PPTP vpn users also.

I've got c3750g with 12.2(55)SE.When I try ifSpeed (1.3.6.1.2.1.2.2.1.5), i've got 1 peak 999999999 and then only 0. Polling is 1 second.When I try ifHighSpeed (1.3.6.1.2.1.31.1.1.1.15), I've 0 also.When I try ifInOctets from snmp-v2 MIB (1.3.6.1.2.1...

my mrtg setup current only gets/graphs bandwidth utilization on our 800 and 1800 routers and a few ASAs.  is there a way to get/graph temperature and cpu utilization etc.?

I started a RME Inventory EoS/EoL Hardware Report on devices and got the appended error log. Cisco.com and proxy authentications seem to work well.Any idea how to solve this problem?ThanksWolfgang

All,I've been going back and forth with development on a way of best leveraging a log rotation capability in our newly deployed LMS 3.2 rollout on Solaris 10.My issue:As of now, we use the services facility built into Solaris to start/stop the syslog...

Hi there, Im trying to configure our cisco catalyst 4948 switch management port. I have gone through this document http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/12.2/50sg/configuration/guide/sw_int.html#wp1138747 i have created ip vrf mgm...

Recently upgraded to a DROID and any SMS messages sent from LMS are now extremely limited. I get the Event ID and just the title of the Alert ID line, that's it.ALL SMS came over fine before using Windows-based phones and Blackberries. The ISP is the...