Network Management

LMS 3.2 not forwarding SNMP Traps

I am using LMS 3.2 and under DFM... Notification Services... SNMP Trap Notification, I have a Subscription set up to forward Traps to Unicenter 11.1. I have tried a combination of sending Alerts and Events, Critical and Informational, Active and Cle...

Resolved! Trouble Adding Ad Hoc Target in IPM 4.2.0

I'm attempting to add an Ad Hoc Target to IPM to measure performance between our network and a server. It is pretty self explainitory in IPM on how to add a new target. I've gone through the process of clicking on "Add Adhoc Target", I put in the ...

Resolved! Can't access ciscoworks homepage using my browser.

Kindly help, i can't access ciscoworks homepage using my clients browser.

Network Monitoring Tool

Hi all,I am in a discovery phase of trying to find out what is out there for Network Monitoring. Beside realtime and historical reportings I am also looking for something that can help in troubleshooting LAN/WAN related issues. For example: I have us...

LMS 3.2 Can't get devices by sysname in Device Discovery list

Hi,I can't obtain a list by sysname for the discovered devices. I just get a list by IP addresses. What could be wrong?The Global settings of "Device Discovery" are :"Preferred DCR Display Name" : HostnameUpdate DCR Display Name"Preferred Management ...

Resolved! MD5 file

Hi all,how can i get a backup md5 file of our router?. By tftp?Thanks

snmp query on a dhcp server (low routers or L3 switches)

Hello,is possible to monitor dhcp binding or free addresses using snmp? I found the following MIB: CISCO-IETF-DHCP-SERVER-MIB, but this MIB is supported only on the Cisco 7300, 7200 series.:-( When I tried snmpwalk on the Catalyst3560, but the CISCO-...

LMS 3.2 Installation - Solaris 10/09 Patch Conflict:

Hello all,We are running Sun Solaris 10/09,working on installing LMS 3.2.As per documentation,attempted to install the two recommended patches,127127-11 and 122032-05.The 127127-11 patch is already contained in this OS packaging.The second recommende...

cisco catalyst 2690 switch vlanTable

Hi,I have a cisco catalyst 2690 switch.I want monitoring IP, MAC, and Port Address.I use this docu: http://docstore.mik.ua/orelly/perl/sysadmin/ch10_03.htmThis works great:htvtef7-nagios:/ # snmptranslate -On BRIDGE-MIB:dot1dTpFdbTable.1.3.6.1.2.1.17...

Regarding configuration changes reports in LMS 2.5

HiI am having LMS 2.5 installed.I want step by step configuration for generating report ofconfiguration changes made on devices.I have tried with change audit plus syslog but unable to generate report.What i need is mail should be sent on configurati...

Resolved! Upgrade RME 4.0.5 to RME 4.2 in LMS

Hello All,We have a LMS server (2.6 Version) and we want to know if is possible to do an upgrade from RME 4.0.5 to RME 4.2.Is possible?Thanks in advance

Interface Errors with connection to F5's

We are seeing input errors on all the interfaces that connect to our F5's.We have checked the duplex (hard set to 100 full both ends, swapped the cable and switch interface but not changed the F5 as all the interfaces have the same issue on different...

monitor graph

Hello ,Although this is non-cisco , wanted to get an opinion on my query from folks here.Attached is an image from mrtg output of a link. It has been observed that for past few days, the graph levels out as seen in the image file.Anyone, please help ...

Syslog automated action is E-Mail, not CONFIG-FETCH

I noticed today that configs don't seem to be updating in the shadow directory. When I goto RME/Tools/Syslog/Automated Actions, the Config Fetch automated action (there by default?) is set to a type of E-mail. I would have sworn that it used to be se...