Network Management

Resolved! LMS 3.0.1 with DEC 2007 update

Hi,I have installed LMS 3.0.1 with Dec 2007 update,i have done custom installation and after that i installed 2007 update,after completing installation and update ,when i start LMS the process of LMS are not coming up for very very very long time and...

Resolved! Syslog messages

Hi,I would like to know how to send certain syslog messages to certain hosts, and block certain others.For instance, I want to send the following types of syslogs to the following hosts:%SEC-6-IPACCESSLOGP xyz.abx.com%SW_MATM-4-MACFLAP_NOTIF xyz.abx....

Problem with Cisco router as DNS server

We have a Cisco 1841 router. we have configured it to act as primary DNS server and also as caching/forwarding DNS server. It is working correctly when queried for domain for which it is authoritative server. But when we query for other Internet site...

Reflexive ACL on a switch interface

Is there any reason a reflexive ACl will not work on a switch port? I see that most examples pertain to routers. We have a 4510 with a Sup 6. I have not tried it yet, but here is the config I came up with :ip access-list extended internal_aclpermi...

IPM 4.1 stopped working, IPMProcess service won't start.

IPM 4.1 stopped workingOn our LMS 3.1 server I noticed that the IPMProcess was listed as "down" on the System tab. Checking the IPM tab displays "Error in communicating with IPMProcess or IpmDbEngine. It may be down or not yet up. Please make sure ...

Resolved! LMS 3.2 Inventory Collection failing

Inventory collection is failing for some devices. I ran into this on 3.1 but thought issue was supposed to be fixed in 3.2 I'm attaching IC_Server.log. An example device is 10.69.130.57

Resolved! Is it possible to restore one backup from LMS3.1 to LMS3.2?

We've installed LMS3.2 in our site but I would like to restore an old backup file from LMS3.1

Resolved! Common services 3.1.1 Process problem

Hi,Some of the process such as CS Discovery,EDS-TR,FH Purge task,in common services 3.1.1 are never started and also transient terminated even though when i manually go and start them.CVDeviceSelector.log is not rotating after specifying in below com...

PSIRT Summary Report always blank

HiI am trying to do a PSIRT Summary Report using RME 4.1.0 against all 2000 device in my CW inventoryThe report always shows as successfully but is always empty. (which I don't believe)I have wireshark on the CW server and can see the PSIRT data in p...

Cat 4500 'show diagnostic' - is there a mib for the output?

Is there a mib that will return the output of the show diagnostic command for a Catalyst 4500?Thanks, John

LMS 3.2 - CM DataCollection Metrics Report doesn't work

Hi there,performing CM DataCollection Metrics Report via CW2000-Portal or direct URLhttp://<ip>/campus/discoveryMetrics.doResults in not showing the last DataCollection Cycles and displaying error-message"Data Collection is in progress. Latest data c...

Resolved! CSS11506 performance report ?

Is there any tools for "Cisco CSS 11506 Content Services Switch CSS11506" to provide performance report?

net-snmp

I have a question related to mib information from Cisco ASA. I am trying to pull current active users from ASA through snmpwalk and I am using "snmpwalk -v 2c -c XXXX 10.1.0.1 1.3.6.1.4.1.9.9.171.1.2.3.1.7and I got list of ip address, is this really ...

RME 4.0.6 Device Package update failure

Hi,i have downloaded a lot of new device packages for the RME 4.0.6. If i install this packages i get the following error message.Installation failed for product [Resource Manager Essentials] with message : com.cisco.nm.xms.psu.packagemgmt.InstallerE...

Resolved! LMS3.1 - Memory Insufficient Error Message from 12404 router

Hi,Just wonder what is the meanning of this fault message. If only show up in DFM but not is router logging. What is the action require.See attachement for DFM fault message.PRIMPLS2PE#show memory summary Head Total(b) Used(b) ...

Network Management

Forum Posts

Resolved! LMS 3.0.1 with DEC 2007 update

Resolved! Syslog messages

Problem with Cisco router as DNS server

Reflexive ACL on a switch interface

IPM 4.1 stopped working, IPMProcess service won't start.

Resolved! LMS 3.2 Inventory Collection failing

Resolved! Is it possible to restore one backup from LMS3.1 to LMS3.2?

Resolved! Common services 3.1.1 Process problem

PSIRT Summary Report always blank

Cat 4500 'show diagnostic' - is there a mib for the output?

LMS 3.2 - CM DataCollection Metrics Report doesn't work

Resolved! CSS11506 performance report ?

net-snmp

RME 4.0.6 Device Package update failure

Resolved! LMS3.1 - Memory Insufficient Error Message from 12404 router

Cisco + Splunk: It's a new day for your data.

Speed & Tech: Unveiling the Cisco-McLaren F1 Partnership

Congratulations to all the August-October 2023 winners!

A new chapter of the Spotlight Award begins!

Announcing Resources That Guide You to Success

EEM action event-default

Change aging-time for a bridge-domain on Cisco NCS520

PoE y teclado

ccna 200-301 v1.1 study material

Can access hosts in management vlan either or asa management ip

Configuring IP Phones to a Router that is already Configured

DHCP - Default Gateway not populating on PCs

Multiple SNMP server configured on a switch

Searching for Cisco Nexus 9k internal SSD serial number

Simplest way for tunneling layer 2 traffic?