Hi, I have a 6500 that is logging most activity from what I can tell. Acl entries are logged and I can see when login attempts occur. However, when an interface changes states there is no logging enrty. Here is my logging config. logging userinfologg...
Forum Posts
Hi all, I've been working on a test setup with Business Dashboard and am running into some problems I can't seem to solve. The setup:Cisco Business Dashboard running in Azure on Ubuntu 16.04Network EquipmentRV340 router RV340-K9-G52x Business 250 Sm...
Hi, Can the result of "show crypto accelerator statistics " is IPsec throughput?If not, do we have a command to check that?ThanksLoc TA-FW# show crypto accelerator statistics Crypto Accelerator Status-------------------------[Capability] Supports...
Hi, We have two Cisco FPR-2110 set up site to site vpn. We tested without firewalls, the bandwidth between two sites is 500Mbps. But when we have the Firewall set up site to site vpn, the maximum speed we can have for a TCP Iperf3 test is 150Mbps. D...
Hello, I am new to Cisco Modeling Labs, I am trying to configure a topology with ansible through the DevBox, I can ping the hosts, but everytime i try to execute a playbook it gets stuck forever on "running the handler": I have looked around and may...
Resolved! SVI and Static MAC
Thought I would put this out there as I can't find an answer to this question. I will purposely not include all the history as I am asking a specific question. I am trying to add a mac-address command to a new L3 switch's SVI interfaces so the MAC...
Hi; Our customer has prime 3.3 version. How can we update to the 3.8 version as quickly as possible.how is the process
Добрый день Ребята настроил vrrp на cisco для bsc с bsc есть пинг до bvi но они не пингуют мой виртуальный гейт.В чем может быть проблема прошу помочь
Hi!I am new in networking and I am trying to setup this networking.I have supposed that I have these devices possible:layer 2 switch, 24 port FE and 2 ports GErouter, 2 ports FE, 1 wan port(it doesnt metter, fiber or any)In the router I have these ip...
Hello, I need to configure an S2S VPN between Firepower and RRAS, without success. There is always an error in pre-shared ikev2 authentication.Has anyone managed to make it work between these two products?
When trying to login to Cisco.com from Administration / Licenses and Software Updates / Software Update it fails to reach Cisco.com. I know the credentials I am using are good and I can telnet to cisco.com port 443 from the CLI of Prime. I can also ...
Hi everyone! I have a problem with a couple of switch cisco Catalyst 3750. I have cameras Hikivision connected to the switches and work very well for a few weeks, but now some of the ports set down and the cameras don’t work.When I shut/no shut the i...
Hi all,We have CISCO 3925 router in our organization.We need to block the access of certain websites such as facebook,orkut,youtube etc...Pls suggest how to do it using CLI or cisco configuration professional.Thanks in advance...
Hello,Does anybody know the OID that tells whether the interfaces on a switch are configured as switchport mode dot1q-tunnel for catalyst switches 29/35 etc.?
PI/admin# dirDirectory of disk:/4519816219 Mar 31 2021 13:59:37 PI-Upgrade-31x_32x_33x_34x_to_3.7.0.0.159.tar.gz20 Apr 01 2021 15:43:26 crash4096 Apr 01 2021 15:26:02 defaultRepo/4096 Apr 01 2021 16:37:15 ftp/16384 Nov 18 2017 12:52:18 lost+found/409...
