Hi,
In MDS device we were not able to post data in below mentioned URL, We were get 404 Error
https://xxx.xxx.xxx.xxx:630/api/mo/sys.json
But the same URL, we were able to successfully post data in N9K device.
We have followed the below mentioned...
Hi,
I am trying to access Nexus api through the feature nxapi command in nexus 5k device. but the api are not responding. Attached screenshots for reference. The
System Version : 7.3(4)NL(L)
Nexus 5548
HiI read about WCCP support on Nexus 7710 and it seems it is supported.I have two questions about this feature:1-Does this feature support IPv4 and IPv6 or just IPv4?2-Should I enable routing on IPv4 and IPv6 for having this feature?Thank you
We recently upgraded to nxos 9.2.3 Cisco 9k. Ever since then we have lost communication to our monitoring system. I have taken these steps for troubleshooting purposes. Below are the commands that were working before the upgrade snmp-server user Fxx...
HiThere are two types of FAN for N7710:N77-C7710-FANN77-C7710-FAN-2 Is there any consideration or restriction for choosing the second generation regarding FAB/SE/cards. This model is not available in Power Calculation tool...Thank you
Hi I am searching about different I/O Modules of Nexus 7710. There are three M3 Modules for this model:1- N77-M312CQ-26L2- N77-M348XP-23L3 - N77-M324FQ-25LI want to ask are these modules supported on "N77-C7710-FAB3" and "N77-SUP3E"Some documents onl...
Hi All, Is it possible to use encapsulation dot1q and second dot1q on a nexus 93180-yc? I am terminating 4 service provider WAN links on 2 93180, 2 per unit. the Service provider is using double tagging for some of the vrfs. I can't see the second do...
Hi I'm trying to convert a 9336C-FX2 switch from ACI software to NX-OS v9.3.5 and I'm following this guide:https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/93x/upgrade/guide/b-cisco-nexus-9000-nx-os-software-upgrade-downgrade-gu...
We have already configured VPC peer link setup. But it only configured for one module. How can I configure another module to reduce the possibility of a failure. Actually I don't have much knowledge of configuring VPC peer link. Please advise.
We have found out that we can "POAP" downstream switch on a non-LACP port-channel. Here is the configuration on the uplink switch:interface port-channel101 no switchport mtu 9216 no lacp suspend-individual ip address 10.10.100.100/31 ip router is...
I am planning to upgrade a Nexus N9K with 2 supervisor modules. Is the process the same as upgrading a N9K with 1 supervisor module. When I upgrade a N9K, I use the following command: install all nxos bootflash:File_Name Thanks!
Dear Buddy,I am facing with a weird issue on Nexus 3K (A & B)in my customer.We have a pair of Nexus 3K are connected by 3 of 10G fiber as peer-link and a keep-alive link.On each switches, we have Interface Vlan 1 and configured HRSP. The issue is 2 s...
Recently, works have begun to arrive that the free memory on the Cisco Nexus 3064 is running out.Notices have an appearance:CRITICAL. Usage 86% of Available MemoryMemory now has 3 statuses:# show system memory-thresholds
System Memory thresholds:
Cri...
Hi,The following low-severity issue "Interface-name, No answer from host" is frequently appear in my NMS.Not much information available online about this issue, appreciate if someone can assist interpret this log message?Thanks
Hi,I am looking for a way to get the LLDP and CDP information of each ethernet-port of a fabric via REST-interface of DCNM?Infrastructure:DCNM, LAN Fabric, Version 11.3NK9-switchesIs this possible? Can someone give me a hint.... ThanksJuergen
