CCM 4.0(2a). I have a number of broadcast huntgroups. When a call is received by a user on a line which is in a huntgroup the transfer softkey is greyed out, so users cannot subsequently transfer that call to another DN. Is this a known issue ??
CCM 4.0(2a). I have a number of broadcast huntgroups. When a call is received by a user on a line which is in a huntgroup the transfer softkey is greyed out, so users cannot subsequently transfer that call to another DN. Is this a known issue ??
We are attempting to communicate b/w a 3725 and our Rolm PBX. We must use an analog T1 because our Rolm doesn't support digital trunks at this time. We have an VWIC-2MFT-T1 installed in the 3725. I am not sure how to set up the gateway trunk in CC...
I've got an analog phone hooked up to my 2651XM and when I try to dial my Meet-Me number that has been created on an IP phone I hear the beep on the IP Phone indicating that someone has joined, but on my analog phone I just get a busy signel... Anyon...
I see that in CCM4.1 there is a new phone (7961).Does anyone have any info on this new phone?Thanks,Jim
Is there a limit to how many dial-peers you can have on a given RSC?
Can CSA(secure agent) be applied on ICS7750? It's system manager 2.62 and CCM 3.3 with os 2000-2-5sr8, unity 402 with os 2000. Any link details that? Thanks
Is it possible to have 1CM to connect to 1GK using multiple trunks and zones? (e.g., trunk1 is created using GK and zone 123, and trunk2 is created using same GK but zone 456?)
I need to configure a 2610 using a VIC2-2FXO to workin in H.323 with CCM 4.0. I need some config examples for this. Any help?
Is ccm-manager command supported on 1760. If so which version. I have seen the statement mentioned below in Cisco command reference where it says it is supported on 1760 but could not find the IOS software.12.2(11)YU This command was implemented o...
We have CCM 3.2(3) and PBX dual intergration with Unity aslo. The problem is this, we can call PBX phone and Cisco IP Phone each other, but couldnt see caller-id on both side.I heard that T1 PRI will help, but I also heard T1 CAS with some type of s...
I am currently working with a customer who does not use an outside access code. They are currently using @ route patterns. A new customer moved in with extensions 1000-1099. The problem is 101 is a transit network and with no outside access code the ...
Hi!How can I force a CME gateway (QSIG PRI) to send name as Facility in q931 and not as Display IE?The "isdn outgoing ie facility/extended-facility" command did not help.Thanks
Hi, I was installed Cisco Unity 4.0(4) with Exchange 2000 and all works fine, but when I try to view Message Activity Report and Failed Login Report, the message "Report Failed" appears in the Monitor Status Reports Queue. When I run the Subscribers ...
I would like to use a couple of the lines on a 7960 to momitor if my coworkers are busy. Ihave tried setting them up as shared lines on my phones.I can see that the line gets a call, but I can not see if the line is busy. Is there any way of doing th...
I have a 1760 with 2 FXS ports.I connect FAXs on both FXS ports and I try to make a call but it's not succesful.I can call a remote FAX (VOIP call) with no problem, but when there is an incoming call, the FAX answers the call but cannot handshake and...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-23-2024 11:56 PM | ||
08-21-2024 05:48 AM | ||
07-17-2024 05:55 AM | ||
07-15-2024 12:39 PM | ||
07-09-2024 04:24 AM |