I have a voice gateway, 8 lines, while 8 calls there, there are still more calls coming, of course, the coming calls failed, how to prevent them on cisco gateway ?THanks
I have a voice gateway, 8 lines, while 8 calls there, there are still more calls coming, of course, the coming calls failed, how to prevent them on cisco gateway ?THanks
Hi... Everywhere on CCO I could find only examples on how to connect two PBXs in a following manner: PBX-E1QSIG-Cisco---WAN---Cisco-E1QSIG-PBX I could not find any scheme where there is a cloud of PBX-s, or at least three. But what if I have to conne...
I have a CallManager 4.0(2)a installation which, for the purposes of integration with an third party CTI product, requires 5 DNs associated with the one CTI Route Point. With systems prior to CCM 4 there was never a problem doing this, however with ...
Folks, I keep getting this message in the even log og my CCM. The callmanager is not even in production yet. Does someone know why i should be getting this messages. Anything i can do to stop these messages, why are the phones looking for MTP ...
Hi. I'm trying to install the Dialed Number Analyzer on the Publisher Server on CallManager 4.1(2) but the installation is failing. It is saying "Failed to unregister Dialed Number Analyzer Service"Any ideas,-Jose
Hi AllAnyone have any ideas as to where I can download some more ring tones for my 7912G's. I am running Callmanager Express 3.2.Thanks
I would like to find out if a Calling Party Transformations in a route pattern will over ride the device's external phone number mask and pass the phone number to the PSTN?
Hi, I have just configured the fxs card in our CM for all 24 ports. We need to use 4 of these ports for a fax server. I have assigned numbers to 4 of the ports. I then created a Pilot Point, and added the 4 numbers above into a hunt group. Now wh...
I have a 2610 router with 2 FXO ports. I am using 2 POTS for inbound and outbound calls. The last 4 digits of those 2 POTS lines are 7314 and 7324. I am having trouble configuring SRST to receive calls from those lines. Any help?
we are running CM 4.1(2), and I see that there is an option to add a 7914 now to the 7970 phones, but there is not a phone button template for that expansion module. Is the 7914 supported on the 7970? Is there a trick to making it work? Thanks, Corey...
Hi, I am new to cisco. I want to join two IP (SIP) calls using "connection create" command which is not succeeding. It is mentioned in the cisco IVR programmers guide that IP-IP call joining is not supported and it will fail without giving any error...
I have an IP Tel installation. The setup has been integrated with PSTN via a gateway with E1R2 digital link.We are experiencing bad echo on some international destinations.Is there any way to find out the exact cause of the problem and how to avoid t...
Recently we have Voice Gateway trunking between PBX and CCM (T1 CAS) that allow call between PBX phone and CCM Phone.However, it wont allow Call-ID send through between PBX and CCM.Someone told me that install T1 CSS (PRI) will solve this problem. I...
Hi Folks,well actually I have a router 3725 with 7 lines (FXO) connected to the PSTN.When I press 7 in the I phones hear the outside dial tone. If I make a phone call from an IP phone to the PSTN, it works well, when I hang up, the line is on-hook. B...
Hi I am going to use IP Telephony from NOrtel systems. This will integrate with Cisco 2900XL and 3500 XL Layer2 Switches.Does we need some different ports for the voice connection.As per my understanding there will be a single Cat5 Cable will connect...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-23-2024 11:56 PM | ||
08-21-2024 05:48 AM | ||
07-17-2024 05:55 AM | ||
07-15-2024 12:39 PM | ||
07-09-2024 04:24 AM |