Hi I have a analog phone which can provide the MWI function connects to Vg248 and ATA-186. I want to ask how can set the MWI function to the analog phone though this gateway ?Thx
Hi I have a analog phone which can provide the MWI function connects to Vg248 and ATA-186. I want to ask how can set the MWI function to the analog phone though this gateway ?Thx
Running 4.0(2a) - internal calls show "From NAME (number)". I need to change the format of the calling number which is showing my full internal DN number. Is this possible ?? If not, can I prevent the internal DN from being reported on the receiving ...
does anyone know if number expansion rules are applied in the order they appear in sh run.I am having trouble setting this up and can only think this is what is happening as, perhaps, a rule on one line is matching the number dialled before it gets t...
Folks, Cisco documentation says that VG224 can be configured as an H.323,Mgcp, Sccp gateway. I want to configure VG224 as a sccp gateway. But can only find H.323 configuration on cisco's website. Does anyone have a sample sccp or mgcp configura...
I am replacing our existing Unity Server with a new one and would like to be able to backup our users from the old server 3.15 Unity and Restore them on the new 4.04 server. I tried using the backup restore DIRT tool, but it says I have to be at the ...
Is it possible to make SMS through VoIP(SIP solution) by using SMS capable telephones.SMS should be able to sent to GSM, CDMA and in it's current VoIP network?
A customer has asked (in a RFP) for the IPT servers to have gigabit fibre optic NICs.Is this supported by Cisco in Call Manager, Unity, IPCC EXpress? I looked in the release notes but there was no mention of this.We plan to propose MCS7835 serversTh...
Onsite the customer we have the problem,thatthe CCM doesn`t disconnect the current call progress when the public sitesend a Disconnect with cause value NORMAL UNSPECIFIED.The call is disconnected after 40 second (timer expired) when the public site ...
I'm using CCM 3.3. I've set a 7940 as a PLAR using " Hotdial on IP Phones with CallManager Configuration Example". When I go off hook I recieve an immediate fast busy.
Can anyone tell me which version of Cisco Call Manager supports/will support SIP?
Hi,The network management centre has reported that there are several SEP devices in different regions/countries making 100's of DHCP requests.One device over 800 requests Has anyone seen this before and what could be the reason for it? Allan
We are implementing a pilot AVVID project for about 8-10 IP Phones. Cusotmer has a PBX and a Meridian Voice Mail System along with a Nortel Software "SIM RING". The Sim Ring software will allow both Nortel phone and IP Phone ring a the same time. ...
I got a problem of getting SIP to work behind NAT. The SIP signaling works fine as the endpoints can call each other but there is no voice heard. I had configured statuc NAT to map the private IPs to the public IPs. I got 2 VPN's ( A & B ) sharing th...
I have three 7960 IP phones that reset and reboot every 30-60 minutes. Any thoughts on what can cause this behavior?There are several other phones on the same switch and call manager as the problem phones.Thanks,dk
Team,I am just wondering in CallManager 3.3(4) SR2, is there a way to re-route a call based on CLID? Let's say that we want to reroute a call when the calling number is from one specific PSTN number. All other CLIDs would route to the particular DN...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-27-2024 02:35 PM | ||
09-24-2024 05:35 AM | ||
09-19-2024 05:56 AM | ||
08-23-2024 11:56 PM | ||
08-21-2024 05:48 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |