Other Collaboration Subjects

Hello,I'm trying to find in call manager place where I can change 'voice vlan enabled | disabled' setting.I can't do that directly on ip phone, because this function is not active. Documentation tells that I should change that on CCM.Unfortunately I ...

Hi,I want to reload the BIOS image in my ATA 186 series device. How do i.Thanks,sam

I had started a new server upgrade for the inhouse CallManager about a month ago but got interrupted an never cutover to the new 3.3.2 cluster. Since then, the 3.14 CM has a bunch of user/phone changes. Is there any way to reimport the 3.14 DB into t...

Understand there is packatization delay when voice across IP wan. G.711 uaually sample the codec 20ms for 20 bytes, this is the packetization delay. Here is my scenario:IP phone-LAN-GW-PRI. There is echo even calling local PSTN phone. Usually IP phon...

Hi Guys!I have a 2651xm router with an aim-atm-voice-30 module and a wic-2mft-t1 card. I am trying to configure pri on the first controller for my access to PSTN, and channel group for data connection to a remote site on the second controller. I mana...

Hi,Have a issue where FAX calls come in a PRI and go to FAX machine on a FXS port on the same router. So there isn't any VoIP involved, just a call in PRI and out the FXS port to FAX.We areseeing where 20-30% of FAX's do not complete. Anyone have any...

Ok I have a large LAN/WAN enterprise network with some mix of old bay stuff (data only) and cisco data/VoIP. I have 23 remote sites (min of a T1 1544mb to each remote site) I currently have 3 of the remote sites on VoIP with minum problems (Echo) wit...

I trying to install softphone v3.1.3 on a HP tablet 1100 PC OS is MS XP. SP installs with no errors, lines show correctly, comes of hook and provides dial tone, the problem starts when you dial any number. you dont hear any ring or conversation behon...

Does any body know if a 2621XM can handle 4 Voice T1s (either CAS or PRI - dont cares)...The modules used areNM-HDV2-T1/E1 - This module has 2 on board T1 ports and a VWIC slot.The VWIC used is VWIC-2MFT-T1.The above hardware should give me 4 T1s on ...

Is there a way to make shared lines on different IP Phones to Auto Answer. I'm trying in CCM 3.3(3) but it says Auto Answer on shared lines are not supported.I was trying to simulate Paging Capabilities using the Auto Answer with Speakerphone feature...

Hello,we have several Cisco IP Phone 7940.We have the firmware P0S3-06-3-00.So we use it as a SIP Phone.I need to configure Softkeys.I know the SIP firmware supports CMXML to version 3.0.So I cannot use the SoftKeyItem.I know it should support BTXML....

helloi have a router with CME 3.0 (1751) with which i configure two ip phones that communicate successfully.now i want to establish a communication between one of the 2 ip phone and a PSTN phonehow can i do thatthank u

I have CTI-Ports with the Information on the Caller-ID with the respective service (i.e. Sales, Service, etc) and I would like for the agent to see that Caller ID in order to respond to the customer (i.e. same agents taking calls from sales, service,...

Hello,does anyone know when the SDK with support for the enhanced features (eg. Java virtual Machine etc.) of the 7970 will be available ?Thank youBeat

I see that CRS 3.1(3)sr1 is posted out on Cisco. Do you know what the big difference is between 3.1 (2) and 3.1 (3)? Also, how do i obtain the 3.1(3) bits?