Other Collaboration Subjects

Hi,We have a Unity 3.1.5(200 Users,12 Sessions,VM) integrated with CM with the following config-Compaq DL320,HD-17 GB,RAM-256 MB,PIIIC:\-6 GB,Unity is installed in this drivee:\-11 GB-Exchange 2000 is installedSubscriber created-Around 120 System is ...

How can i see, which network/port settings the ata has negotiated with a switch? There is a case, where a switch tells me a 100MBit fd connection and a cdp message on the voice gateway (Cisco2621XM) tells me, that the ata (his mac address) is seen as...

First I am trying to set up a cheap ACD solution for a Tech support 1-800 number with 4 support techs and one admin, In theory the Admin will take the calls then transfer it to an availalble Tech, however if she is not at her desk or is busy then It ...

Does anyone know if Intuity is able to support two PBXs simultaneously? I am looking to connect CCM to Intuity via SMDI. The Intuity currently attaches to the G3r via analog and uses Ethernet for signaling. Can CCM use the same Ethernet for signaling...

Is anyone successfully running Call Manager 3.2(2c) and Attendant Console 1.1(2a)? I know the read me for Attendant Console lists Call Manager 3.2 2a as the newest tested version. I also noticed that the post date of the read me file is prior to the ...

We have 3 AC's, usually only one logged in at time.problem is that intermittantly it will pass calls to the nightbell(last entry in the hunt group - for when they are logged off)when you check the client, shows logged in, have shut down client and re...

If I upgrade to 1.1.3, do I have to update all clients to the new version ? I have 3 AC pilots, and 3 persons running AC, If I upgrade the CallManager Cluster, the docs do not state you must update the clients, and how will the ac 1.1.3 update effect...

My customer is trying to add a specific subscriber to a private list via the TUI. Everytime they get the message "This recipient's e-mail address does not exist" They can add this subscriber fine through the SA. It appears to be isolated to only t...

Hi,I have an FXS card installed to provide two analogue lines for testing the IPCC installation. At present I can ring from the FXS extensions into the Call Manager and vice versa yet when I try and translation route to the IVR I get fast busy. The C...

I am planning to use the ATA 186 devices to give me analog ports off of my voip system. I have read alot of stuff about fax-relay and fax-passthru and such but am not really clear on what is needed for my situation. All I really want is to be able ...

Hello all,Am I missing the obvious way to view usage in CDR Analysis & Reporting for users who are only configured with Extension Mobility? While I can pull up the users there is no data.Am I not able to run reports for Extension Mobility users?Than...

There are a lot of posts, in this forum and other IP Telephony forums, that discuss the need for Facilities IE support in CallManager. I am trying to pinpoint whether or not it will be included in CM3.3. The following bug:http://www.cisco.com/cgi-bi...

I have a customer whose phones are going into fallback on a SRST gateway, and then reregistering to the call managers quite often. Sometimes they don't reregister very easily. I changed a command that was in the config. Used to be "no mgcp timer r...

Has anyone encountered a reported defect in SPF where if the primary CallManager fails, the phones will NOT register to the secondary CallManager? I was told that this is a problem with the SPF.Thanks,Mike

From a single 7960 phone, I've got one call open on one DN and another call comes in. I place the first call on hold and answer the second call. I now realize I need to have all 3 of us talking together. (Me, the first caller and the second caller)...