I have a 6506 running with an MSFC and PFCIISwitch # sh modMod Slot Ports Module-Type Model Sub Status--- ---- ----- ------------------------- ------------------- --- --------1 1 2 1000BaseX Supervisor WS-X6K...
I have a 6506 running with an MSFC and PFCIISwitch # sh modMod Slot Ports Module-Type Model Sub Status--- ---- ----- ------------------------- ------------------- --- --------1 1 2 1000BaseX Supervisor WS-X6K...
We have an installation of Cisco Clean Access system. We purchased this product believing that the Clean Access Agent would communicate with the Clean Access Server across a router. It relies on a UDP broadcast on port 8905 using the SWISS protocol.(...
I am using HSRP and all hosts are using the active router to forward traffic to the rest of my network. I have noticed that the return traffic comes back through the standby router.well,this will not caused any problem on HSRP but we are facing the p...
Version 12.2(17a)SX3 is one of IOS version of 6509. I can't find the information about how to config routing on 6509. I know most of config command is same with 12.2 T. But where to find the difference between 12.2(17a)SX3 and 12.2T? There is detail ...
Hi All, I'm using c4500 with IOS 12.1.20EW2, my problem is, I can not see link Up/Down on my loggas far as I know in CatOS this will be log automatically... need helpthx
Hi there,I just wanna know if someone has good experience with a cisco router with dual FDDI interface in combination with ethernet interfaces?If so, which cisco router + interface cards are you using and is it still available at cisco?Thanks in adva...
Hi, I use currently SUP1A-2GE and MSFC vers.1 on my Cisco 6006. And I got another Supervisor Engine SUP2-2GE with MSFC2. I was wandering, if it is possible to make redundancy between Supervisor Engine above. If so, how can I get some sample configura...
Hi All,I keep getting this error when attempting to copy running-config to tftp,Switch#copy run tftpAddress or name of remote host []? 192.168.1.12Destination filename [running-config]?.....%Error opening tftp://192.168.1.12/running-config (Undefined...
Between 2 layer 3 switches, is it better to configure a L3 etherchannel, or configure routed L3 links? If you set them up as routed links, you can load balance in excess of the 8 links limitations imposed by etherchannel. This isn't really an issue...
Hi,I am trying to troubleshoot a problem involving ip audit, and was wondering if anyone knew of a definitive list of NSDB signature-id that are implemented in the IOS.Any help would be very gratefully received.Tom.
i have a 3550 smi switch and i want it work layer 3i did that but my main problem is when i want to configure bandwidth limiting by policy it doesnt workand i check the bandwidth with my monitoring tools (solarwinds) and i didnt see any changes.no sw...
What is the difference between 255.255.255.255 and this one 192.168.20.255 ( Network Address 192.168.20.0/24)
Hi there,I haver a some problem with a deployment of DHCP.There is a DHCP server with two address pool.One is with major network of Client contained, another is with secondary.As a example, the two address pool is like 172.30.100.x, 172.31.100.x.And ...
Well i am currently having 2 issues. First and correct me if im wrong but shouldnt an new MFSC (SUP Card) when inserted and it will be functioning as a secondary should syncro the current config from the primary? well in any case mine didnt so i had ...
I have a question about communication from one host with an inside source static to another host with an inside source static through the public address. For example, I have a workstation with a 10.x.x address that has a public static of 199.190.x.x ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM | ||
11-08-2023 03:38 AM |