Hi my situation is freeradius give the switch wrong attribute parameters.The users config file says: Username Auth-Type == EAP, User-Password == xxx Framed-Type = Framed, Tunnel-Medium-Type:1 = 6, Tunnel-Type:1 = 13, Tunnel-Private-...
Hi my situation is freeradius give the switch wrong attribute parameters.The users config file says: Username Auth-Type == EAP, User-Password == xxx Framed-Type = Framed, Tunnel-Medium-Type:1 = 6, Tunnel-Type:1 = 13, Tunnel-Private-...
Hello,does a PC program for windows laptop exist where I write an IOS on a PCMCIA Flash Card (C72xx or C36xx)?Thank´s a lot.Thomas
I am testing the failover speed on my 6509 with dual 720's. Using just a continual ping across vlans as soon as I do the failover command I see a slight delay but well within the advertised limits so that is good. However a minute or so later, I assu...
I need to http to the catalyst 2950 switch and monitor it, but I don't know how to add an IP address to it - can you help?
We are designing a LAN with a layer 3 switch as a core (4500) and plan to have redundant links to every network. So I'm wondering if Cisco 4500 can handle multiple HSRP connections on many different interfaces.We currrently want to have 6 different H...
Despite the fact that Cisco does not support enhanced routing protocol features on the 4500 SUP II + We have noticed that EIGRP and OSPF are configurable on the 4500 w/ SUPII+. The switch is capable of supporting RIP V2 and has Hardware-based IP Ci...
Hi, I'm trying to determine if the following configuration is possible:routerA } ___ VLAN A } } 3550- ( (___ VLAN B (routerBWhere the 3550 essentially has two uplinks, and two VLANs to match. No direct routing between the two VLANs is...
I have new C3550's setup but when I'm console in to the switch I cannot ping anything. Any ideas?show run,version 12.1no service padservice timestamps debug uptimeservice timestamps log uptimeservice password-encryption!hostname New3550_1!enable secr...
I have a 6506 running with an MSFC and PFCIISwitch # sh modMod Slot Ports Module-Type Model Sub Status--- ---- ----- ------------------------- ------------------- --- --------1 1 2 1000BaseX Supervisor WS-X6K...
We have an installation of Cisco Clean Access system. We purchased this product believing that the Clean Access Agent would communicate with the Clean Access Server across a router. It relies on a UDP broadcast on port 8905 using the SWISS protocol.(...
I am using HSRP and all hosts are using the active router to forward traffic to the rest of my network. I have noticed that the return traffic comes back through the standby router.well,this will not caused any problem on HSRP but we are facing the p...
Version 12.2(17a)SX3 is one of IOS version of 6509. I can't find the information about how to config routing on 6509. I know most of config command is same with 12.2 T. But where to find the difference between 12.2(17a)SX3 and 12.2T? There is detail ...
Hi All, I'm using c4500 with IOS 12.1.20EW2, my problem is, I can not see link Up/Down on my loggas far as I know in CatOS this will be log automatically... need helpthx
Hi there,I just wanna know if someone has good experience with a cisco router with dual FDDI interface in combination with ethernet interfaces?If so, which cisco router + interface cards are you using and is it still available at cisco?Thanks in adva...
Hi, I use currently SUP1A-2GE and MSFC vers.1 on my Cisco 6006. And I got another Supervisor Engine SUP2-2GE with MSFC2. I was wandering, if it is possible to make redundancy between Supervisor Engine above. If so, how can I get some sample configura...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM |