Other Network Architecture Subjects

So I have to configure a menu for some commands on the router, so far all is working. One problem I have is for commands that are not static, in the sense that they require some input such as "ping" or "traceroute".I need to be able to allow the use...

I'm using the following modules in a Cisco 3725WIC-1SHDSL 1-port G.shdsl WIC (two-wire only) WIC-1SHDSL-V2 1-port G.shdsl WIC (two- or four-wire) I've tried the following IOS versions :c3725-entbase-mz.123-11.T.bin&c3725-entbase-mz.123-11.T2.bina...

Suppose I have got this scenarion:My LAN consists of one Cisco switch and 5 PCs. As we know tha LAN uses MAC address, How can the switch translate IP address to forward packet from one PC to another when I use ping command?

Can NBAR be used for selective URL redirection ?i.e Can NBAR class be used in policy based routing? I have this ;class-map match-any httpWEBSPHERE match protocol http url "XXX*"match protocol http url "YYY*"route-map redirect-url permit 10 Router(c...

HelloFollowing topology:- 2 routers in confed 65000 (a1/a2)- 3 routers in confed 65100 (b1/b2/b3)- BGP sessiones between all of themNow a prefix advertised from a1/a2 to b1/b2/b3 gets readvertised from b1 to b2, b2 to b3, b3 to b1.If a1/a2 withdraw I...

I need to connect 2 offcie branch. Each office has its LAN:- office1: 192.168.0.x / 24- office2: 192.168.1.x / 24I have 2 bridges connecting the sites:- one laser 100Mbps bridge (primary)- one radio 11Mbps bridge (backup)I have to make a choice in th...

Hi, I want to configure two MSFC`s in the same chasis. By example I have in the first MSFC Interface Vlan 56ip address 156.175.20.1 255.255.255.0ip helper-address 156.175.28.202If I want to configure the second MSFC for HSRP do I have to change the ...

Is it possible to use a 3550 to route between two vlans and be able to control only certain pcs being able to access one of the vlans and the others to be restricted. Also can you use a 3550 to route between two networks(not vlans)? I am learning t...

I have two 2620 routers and plan on upgrading the IOS to 12.3 (mainline). For the IOS BIN I selected (IP feature set) Cisco recommends that the minimum amount of memory in the system be 32MB and minimum flash br 8MB. I have 8MB of flash, but only 26...

Dear AllIf I have got this scenario:PCs and switch, PCs (A,B,C,D) on segment1, and PCs(1,2,3) on segment2.If I tried to use ping coomand from PCA (segment1) to PC2(segment2), Now as we know switch will allow the frame to pass from segment1 to segment...

Is there a command that I can enter to find out what version of SNMP the some of my switches?TIA

Hi,I've a chassis config for a service provides that use MPLS.the question is: When do I need to use different kind of CFC,DFC and memory quantity for my modules ??The chassis config is:Cat 6509 NEBS Chassis for all Supervisors,No PS,No Fan 1 Unc...

Dear sir : There are some problem when I config static arp table in Switch3750 ? Following is description :Section 1 : If static arp command already config on Switch3750 , then the PC connect to Switch3750 . PC's performance is very bad . Include...

I have a LAN segment with over 100 meters long. Therefore, I use a switch to slove this over-length problem.So, is the user on the LAN can communicate to each other ?Will there be a collision, late-collision ?Thanks for all Pro

Can someone advise on CRC errors troubleshooting techniques. Thank you.