Other Network Architecture Subjects

I have a 2610, with 8 port bri module. I have 4 isdn lines that come in (right now they are in a MS box). I have one local number and one 1800 number that people call to come in. I would like to setup 4 of the interfaces so they accept the call. I ha...

More and more PC's are tagging frames using 802.1Q for the only purpose of QoS i.e. with Vlan ID = 0. How do we configure the switch port when such a PC is attached? As a trunk? Is there any aquivalent for the CatOs command 'set port auxiliary 2/1 do...

I am currently trying to view ESSE alarms with Cisco Info Center. I have found that I need the following mib CISCO-DEVICE-EXCEPTION-REPORTING-MIB in order to display the proper content of the alarm in CIC event list. I can not download this Mib fil...

Over the past couple weeks we have had a strange problem. Network access to an EMC NAS slows significantly for subnets that are not directly connected. Most other network activity seems normal. If the users reboot the problems goes away for a coup...

I have found the sho platform health command to be very useful in troubleshooting high cpu utilization on the 4510R. However, it is not documented well and most of the processes that are running high are not documented at all. Is there a resource for...

I have set up a router as a web server (enabled ip http server, loaded an index.html to flash) to serve a single small web page. This works fine as long as I enter a pre-defined username/password. The problem I have is that I want to serve up this pa...

Hi All,I have 3550 SMI with IOS c3550-i5q3l2-mz.121-12c.EA1/c3550-i5q3l2-mz.121-12c.EA1.bin image. i am trying to apply the inbound as well as outboud policy on 3550 .after applying the police i am not getting the policy on outbound but i can see tha...

I need to know when occur a problem to the X25 cloud Provider. The static route this permanent active.Is some form that static route down when the SVC of the cloud fails?Thanks Martín

I have a customer who has a ISDN Voice PRI circuit. The circuit is terminated on a 2621 with NM-HDV. VWIC-2MFT-T1 and 4 DSP chips on board. The T1 controller seems to be UP. But the ISDN layer 2 status is still at TEI_ASSIGNED. Switch type is Primary...

I have always used the set port host command to set trunking off on switch ports on my catalyst switches. Should I be doing the same on my stackable 2950 and 3500 EI swithes also by using the switchport mode access parameter. I believe this would pre...

I will use two 2651 routers with NM-2V and 2FXO each. Is it possible to communicate calls between two FXO voice channels?Thanks for any help,

Hello,Would you pls let me know the part number of 48 port 10/100/1000 UTP module (fixed ports ) for 6509.Thanks Raju

Hi,What's the syntax for the import file ?I know it was on the forum previously but it appears to have been removed.The nGenius RTM readme file is wrong ...I seem to remember we need something like :automatic, dev_name, IP, ro-string, rw-string,,,[LO...

Hi!I have about 5% disconnections with DisconnectCause=41there is an output of the connectionThank Yoush call h v la 1 GENERIC:SetupTime=2066261 msIndex=1574PeerAddress=4352235850245PeerSubAddress=PeerId=43PeerIfIndex=204LogicalIfIndex=...

We have a network with a single 6500 switch (with internal MSFC). Our buildings each have 3500's as their core. Our 6500 is performing the routing between each building and controls the VLAN's. We would like to be able to send WOL (wake on lan) pa...