Does anyone happen to know if Cisco offers hands-on clases on their latest network gear?thanks
Does anyone happen to know if Cisco offers hands-on clases on their latest network gear?thanks
Could somebody please reference a source that I could read about the exact definition and possible relationship of the following terms :switching fabric forwarding bandwidth forwarding rate how do these interrelate and how do we calculate them ?I wou...
I have installed CW SNMS at customer site. Everything seems to work fine except retrieving configs from devices. whenever i try to fetch a config, i get status "failed". I checked all the necessary attributes via "check device credentials"; they all ...
Is there a way to unlogg a user from CW2K? I have noticed that once i log off, and then log in under Admin, it still shows my personal login as being logged in still!
Hello,I would like to have an opinion on the following configuration for QoS in a Hybrid Cat6509.This is the first time I am implementing it on a production box. The main idea is control the traffic for a specific server in the network.This configura...
I've got some questions concerning T3 technology that I haven't been able to find a clear answer about anywhere.1) What is the difference between Clear Channel and Channelized? I've heard that Clear Channel (B8ZS? I know what this, is Clear Channel t...
We have a 4506 switch with a supervisor IV engine. I configured an ip address to each VLAN interface in the network, and enabled them with the no shut command. I entered the ip routing command, and setup the default gateway to a cisco router that h...
A co-worker and I are trying to figure out the reason for a particular statement in this example...hoping for some help. This example is the Surf & Sand network merger. Our question has to do with access-list 1. The exact line in question is this:...
Quick question here. When I do a trace that goes through a set of routers configured with HSRP, the first hop come back with a result of:Tracing the route to 10.185.20.75 1 10.186.99.2 4 msec 10.186.99.3 0 msec 10.186.99.2 0 msec 2 * * *N...
Hi,We have to be able to provide the total number of packets and bytes switched by the backplane. I amaware of the show system and show traffic commandsat the cli, but is there a MIB or query that canbe run to give this information? Any pointers wo...
Guys,I have been on the software selection tool that cisco offers but have not been able to find the software I need. Basically I have a 10/100 eth module that isn't being detected at the moment, and the error message suggests that i need an OS upgra...
Hy.I Had some problems with Port Security on Cat4000 running 6.3.(4)a There was a recommendation to change to CatOS 8.3.(2)GLX.Now i have still problems to configure port security. The dynamicaly secured MAC Address did not remain on the port after d...
I was doin a policy based routing on a 3550-12t and when i invoke the below commandIP POLICY ROUTE-MAP GO-COREit gives me an error sayin "PBR requires enabling extended routing"I am running OSPF on the vlans.Pls help..Thanks.
Hello,I have a cisco 2611 router and I want to connect this router with another 2611 router.To perform this, i using isdn line configuring with dialer(DDR connection).The problem is that the activity's led start to blink anormaly (very fast) when a p...
I have two 6500 connected to each other with ether-channel(lacp). I have no configured any static cam entries. But when doing "show cam stat" one of 6500 shows:SEORBB0001> (enable) sh cam stat* = Static Entry. + = Permanent Entry. # = System Entry. R...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-23-2024 02:17 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |