Other Network Architecture Subjects

I accidentally restarted a 6506 (switch only) that had an entry in the config calling an image which had been deleted. Consequently, the switch won't boot enough to let me in to delete the reference from the config. I am sure there is a way around ...

I have two sites.On the one site I have a cisco 2621 with two Ethernet interface one for the LANand one for WAN.The bandwidth to the ISP is 512 Kbit/s up and downstream.On the other site I have a cisco 1721 with two Ethernet interface one for the LAN...

Hi, I have 2 questions, one for our own 827-4V, the other for one of our clients, who has the same router. Both were supplied to us preconfigured by the same ISP, who is no longer handling maintenance & I am trying to nail down a problem & some infor...

Hello anyone:When my 3550-24 switch boot,the system show:!!!the switch don't use!!!then the system is hangup?why ?Thanks!

We have a scenario wherein a Customer X has 2 links terminated on 2 routers running EBGP with us. He wants us to load share the traffic towards him on these both the links..We have our internet BW available at our core router. No routing protocols en...

We are running 12.3(5b) on a 7507 with a RSP4. When we perform a "show interface ATMx/y/z.subint" on a functioning subinterface that has traffic, we get zero bytes/packets/cells both in and out. Not on all subinterfaces just of the more important one...

Hi,Am trying to establish a Analogue Dialin to my Cisco 2620 Router having NM-8AM module.Using an External US Robotics Fax Modem for Connectivity from my remote client.I do not get through and just get a irritating noise which I presume is trying to ...

Dear all,We used Cat4006 with 8.1.1 plus Cat4232 with cat4232-in-mz.120-25.W5.27.bin. When we setup the dot1q 2587 vlan on Cat WS-X4013, which is OK for trunk, but on Cat4232 which is not support more 1024 vlan routing, so the Vlan 2587 is not routa...

I want to configure my Cisco 2522 Series router as a DHCP Server for the network. But when i tried to do that there are no commands available for this. Pls tell me how can i do this.I m using 12.0(5) OS in it.Pls help.

Dear Experts,I have a SW-2924C-XL-EN switch.The switch some time could run with the prompt "switch: "However, some time it could pass the POST (as in the end of this message).Do you have any way to solve this problem?Thanks.Nguyen Nhat BinhC2900XL Bo...

Does anyone know if Cisco IOS software that supports IP/IPX W/VIP for platform CAT6000-MSFC2 means that I will be able to have workstations running Novell client and connecting to Novell servers which are located both in the same VLAN and other VLAN(...

I have Cisco 2522 Router. It has bri port(not mentioned S/t or U type), firstly i am confused about this that what interface type it has.I am from Pakistan,in Pakistan external NT1 is used for connectivity(S/T interface).I want to connect my this rou...

I have a 3640 with ios version 12.3.7.T1 Ram is 128 mb and flash 32 mblast night i received this message:Queues messages:*** System received a Bus Error exception ***signal = 0xa, code= 0x1, context= 0x63f229f4PC= 0x6048fed0, Cause=0x420, Status Reg=...

Hi EveryoneWe have two 2600's with an E1 running only data. We have noticed that on occasion we require additional bandwidth but not enough of the time to order a larger line and go to the expense of HSSI interfaces etc.Someone suggested we run stac...