Can Cisco Secure ACS software can be used to support virtual profile AAA service ( to identify the IP profiles for dialed in routers ) for the CISco routers ?
Can Cisco Secure ACS software can be used to support virtual profile AAA service ( to identify the IP profiles for dialed in routers ) for the CISco routers ?
Have an old 2500..types of link mgmt available are switched & pvc drop. The frame net is set up as ANSI or ANNEX D. Which should I use?
What is the max fiber loss a SM LH and ZX GBIC can tolerate before is starts to drop packets or runs into interminttent connectivity? This would be across 1310 and 1550 optical light.
I am having problems adding above 16 standby groups on my supervisor engine mentioned above. I have found the link at Cisco: http://www.cisco.com/warp/public/473/168.html , and this doesn't provide any help. I have an identical sup. engine that I am ...
I have 2 T1s between location A and B. Location A has one 3620 router (R1) and location B has 2 7206s (R2 and R3), with one T1 going to each. The 2 routers in loc B are connected via FE ports to the same switch. I am using OSPF.R2 is sending data des...
Hi, Everyone I just been awarded the responsibility of installing 4 3745 Cisco routers. The local phone company wanted $5500 dollars for the installation and my employer thinks is to much. I was looking at the Cisco website for sample configurations ...
HI all.I use an ISDN cisco for dialing in ms win98 remote access client with chapas authenticate.All works correctly, i assign dinamically the ip to all clients that connect,but the clients does not take the correct default route to my isdn router.Wh...
I had problem with 3620 router w/z 24MICA modem and PRI/CSU(2 T1) module. When I look at "show isdn status", Layer1 was showing "Deactivated", so I check with our carrier(teleco) but they told us PRI line seems no problem.After I tried several fixs ...
We currently have two ways of getting out to the Internet from my location. I have other buildings that come through my location to also get to the Internet. We are trying to point all Internet users to go through the new connection where only traf...
Hi,I have a WAN which consists of two locations, 3640's at each end, connected via Point to Point T1. I just installed a 9 mile wireless transparent bridge link between the two locations. Question, would it be better to by-pass the3640 and plug the w...
Our network currenlty connects to the internet via a 512 fractional T1 through a Cisco 1720 router. We also have 3 isdn lines in house that are used exclusively for video-conferencing. The ISDN lines connect to an ADTRAN NT1 (4 ports) which then conn...
hello,i am having a problem acquiring users on 3512xl switches. i have had ciscoworks obtain users from a couple of 3512's on our network but the rest aren't being picked up. the devices are shown in rme and i have also tried doing a discovery specif...
I am trying to configure MRTG to give me data about utilization on my wireless network. When it's configuration script looked at my radios through SNMP it found some interfaces that I'm not real sure of their translation to the physical world.I've g...
I am running a 3640 at a co-location facility. It is running Version 12.2(5a), RELEASE SOFTWARE (fc1). How do I tell what the port speed of the interface is set to? I've printed out the config, and it just tells me that it's full duplex. I did a "sh ...
Hello all,quick question about proper code for the following configurationCatalyst 5509SUP III GDo I use the SUP III code or the SUP G code?Also, how do I see the name of the actual code that has been uploaded to this switch. The show flash and show...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |