Other Network Architecture Subjects

What is the difference between btwn these 2 types of promptsR1> R1(boot)> I had a dead 2501 with 16meg of flash in it and swapped it out to another2501 that only had 8meg. I put both of the flash simms from the dead2501 into the workong one. After I ...

Could anybody let me know the following:I am aware that the cat5509 had a back plane of 3.6G, i have sup-iii and all the 8 slots populated with WS-X5225R, the ethernet ports in modules in slot 5-7 are having a problem that there is a lot of packet d...

Hi, I am preparing for CCNP exams ,and just did an R&D.Two routers in the central and remote sites are connected with 3 serial links.Static routes are configured in each link.No routing protocol is running.My requirement is that ,I want load bala...

Can some one tell me what the following messages means on a Cisco CAT 5500 version 6.3(5). %SYS-3-PORT_ERR:Port 11/6 RxLengthErrorDrop %SYS-3-PORT_ERR:Port 6/2 RxInnerCRCErrorDrop I did not find any info on CCO about this meassegesThanks for yo...

If i have several routers (remote offices) configured with dialer profile, dialing in to one central router(headquaters) that has a PRI. Do i need to configure a dialer profile for each remote location on the central (headquater) router? or just one ...

When does EIGRP discover its neighbors?When it receives a hello packet from its neighbor or When it receives an acknowledgement of one of its transmitted hello packets.which answer is true?And why?

It is used to config cat3550 and 2950 switches. But I don't know where to download it. Who can tell me? Thanx!!!!

Hello,My name is Thoralf Muschak.I have a question to the following scenario on a IGX 8430 / SWSW 9.2.38.********IGX1 VT Service IGX 8430 9.2.38Source Node: BPX1Source Line: EXT-1 2.048 MHzClock Type: Primary Clock ...

I can not allocate IP address from RADIUS server(cistron). I created user profile with reply items FRAMED-IP-ADDRESS and FRAMED-IP-NETMASK.But Cisco AS5300 put ip address from local pool which is pointed in peer default ip address command. I saw ou...

I have a Cat 6509 and eighteen 3524 and/or 3548's. Obviously I want my 6509 to be in VTP server mode. But is there any advantage/disadvantage to having the 3500's in client or transparent. I would think client, but is transparent use less resourc...

I found a document on cisco web site of how to obtain the backplane utilisation on Catalyst switches 5500 and 5000 using snmp.(1.3.6.1.4.1.9.5.1.1.32 for the 5500 and 1.3.6.1.4.1.9.5.1.1.8 for the 5000 if anyone is interested)I assume the 5500 has 4 ...

In an ISP POP ,there is a 3660 router and an ISDN BRI line is connected to a customer.But now,the higher authorities are asking to keep only one B channel with that customer and configure the other B channel for another customer. Is this possible..?...

Hi all, I am having 512kbps point to point link from my ISP(Cisco 3660 at ISP end) and Cisco 4500 router at my end. I am redistribuing that bandwidth to my inside complex customers through Cisco Catalyst 2900 series switch. I want to limit ...

i have two networks connnect via wan. both networks are on public ip's. the wan is on private ip's. Currently the routers can see one another, however i cannot ping or send packets between this two LANs. scenario is as follows:First LAN with cisco r...

when I start up 2600, It's start Message just as appendix. Then It has no response.I try to start it from Rommon. I have used deferent PC with deferent Standard Break Key Sequence Combinations. But It has no response to any Break Signal. What's wron...