Guys,Why am I getting the following error/warning on my Catalyst 4006 switch:2005 Aug 25 16:06:25 gmt +02:00 %SYS-4-P2_WARN: 1/Astro(4/1) - timeout occurred
I am using L3 3550 / IOS 12.1(22)EA4I have configured 2 VLANs on it, Vlan1 as 10.4.10.65/26 and Vlan2 as 10.232.41.1/24 i have applied access-list as access-list 100 permit icmp any any . I applied it on both the Vlans as ip access-group 100 inip acc...
Hi,We are in the process of buying a new bunch of catalyst switches for our LAN and are considering buying either the Catalyst 3560 or 3750 series. I have checked the specifications and documentation, but I cannot find many differences besides the St...
Hi....I wanna know port-channel configuration.-----------------------------------------interface Port-channel12 ip address 61.102.191.21 255.255.255.240 ip access-group 120 in ip access-group 100 out no ip redirects no ip unreachables ip pim sparse-m...
Hi,I am testing ipv6 dhcpserver in my router but couldn't able to fetch the ip from dhcp server(router).can anyone give some idea how ipv6 works with router ?Regards,S.Hari
I work for a large manufacturing plant that employes Cisco 3750 and 6500 series switches. We are having a problem in using 255.255.255.254 mask on point-to-point VLAN uplinks. Every time, the switch restarts, after the initial boot process, it locks ...
I want to stack one cat3750G-12S as master and a Cat3750G-24T as Slave. I went through the problem of use the proper SDM. As per Cisco recomendation both switches needs to be in aggregator mode. But there is no recomendation for both swicth to be run...
Hi EverybodyI configurate the feature port security on catos with switches 6500, but I have two doubt, first wich is the best, enable age time or put zero value the age time , and second If I enable age time, wich is the normal value to put it.thanks...
Hello,I need to configure a connection from port 24 on one router to port 48 on another. I am told I need configure the port as a trunk and not as an access. I have no idea how to do that. I am attatching the config for the switch. Can anyone hel...
Hi!I am connected to a customer´s network and they have asked me to implement TACACS in my environment that is composed by 2 PPP links, 2 Cisco 2600, 1 Catalyst 3550, 1 firewall (appliance Check Point), 1 Catalyst 2950 and Windows 2000 Professional w...
Hi, I have a switched network with 5 vlan´s. There is a 3550 for routing. I´ve enabled vtp pruning but I am still being able to capture broadcast traffic from vlans 5,6,7 and 8 in the trunk connections that compromises vlan1.I also observe that vtp...
Howdy,I have to deal with some switches that have the 802.1d-1998 flavour of spanning tree. Is there anything really different between the that and the current version?M.
Hi,I've looked through the list of supported models for the Cisco SDM for routers, and it supports 1710 and 1721.Have anyone tried to use it with 1720, or are there anyone out there who knows whether or not it works?Thanks in advance,Rasmus
I need to implement PIM multicast throughout our entire enterprise - about 80 routers, many local, many across T1 links and other higher-speed MOE links.I've looked into using AutoRP with two candidate RP's, but I'm concerned becuase I will have to c...
Hi,In normal sense, I understand that the service-policy should be applied on sub-interface. policy-map Outputclass xxxshape average 300000int fa 0/0no ip address...int fa 0/0.10enc dot1q 10ip address x.x.x.xservice-policy out Outputint fa 0/0.2enc d...
