Hi All, i have 6006 as a core switch. configured 20 VLANs on 6006. i am using 4006 access switch and 3500. Getting heavy broadcast on vlan interface. can anybody give me solutionThanks & Regards,Ciscobuddy
Hi All, i have 6006 as a core switch. configured 20 VLANs on 6006. i am using 4006 access switch and 3500. Getting heavy broadcast on vlan interface. can anybody give me solutionThanks & Regards,Ciscobuddy
If I have got several ip's assigned to 1 interface what should I enable on it to increase performance, is it ip route-cache ??please help
Hi All,get this with a 7200 and NPE200,CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCSelf decompressing the image : ################################################]%ERR-1-SERR: PCI bus system/parity error%ERR-1-FATAL: Fatal error interrupt, relo...
Hi,I try to query my Cayalyst 6513 SUP720 Q-Bridge MIB ( 1.3.6.1.2.1.17.7 ), but it seems not support Q-Bridge MIB. Does the Catalyst 6513 SUP720 support Q-Bridge MIB? ( My SUP720 IOS is s72033-jk9o3sv-mz.122-18.SXD3.bin ), if s72033-jk9o3sv-mz.122-1...
Hello, can we program ACL s on subinterfaces for a routers interface, is it possible ?thankq,kumar
Hello,I recently upgraded a 6009 with Supervisor 1A from CatOS 7.6(5) to 8.4(4). Baseline total CPU utilization before the upgrade was about 12%, post upgrade it sits at about 30%. We have several similar switches throughout our network that we int...
I have a router go down a few times this morning, is there anyway I can monitor it, by debugging or logs etc ?please helpCarl
how do i clear "set vlan 202 6/12" command in cisco 6509? because when i enable "set trunk 6/12 on negotiate 1-1005,1025-4094" "set vlan 202 6/12" is also been seen there, because of this trunking is not happening & get a message in teh console, VLA...
Hi there,I've got a Cisco 806 router with the newest IOS (12.3(15a) or something like that) and it's working quite well except for one thing.Every 5-10 minutes it drops traffic (and my computer actually looses connectivity to the router for just a se...
Hi,We are almost a week dealing with a very instable 6500.What we see is that modules are undergoing a soft reset. When this reset fails the module has a faulty status. Resetting the module mostly solves the problem. But in some cases more then on...
I would like t interconnect two cisco routers for testing purposes, using their serial ports, but still can not find serial-to-serial cable (60-pins each side).Should i make such cable by myself? And where can i get pinout for the cable like this?Tha...
I'm looking for a network device that can perform the following tasks:I currently have a cisco 1721 with 3 ethernet ports (builtin one plus two wics) maybe it could be done with this ?Translate 6 fixed ip addresses residing (inside) on two differen...
I'm trying to configure a Vlan Dynamic Membership but I am not very clear on where do I have to store the database configuration file and wich commands to I have to use to make it work properly.Can somebody help me?What a database configuration file...
What does the state of "OTHER" on the standby Sup2 card in a CAt6500 mean. Reseating the card did not resolve the issue. Is it possible to connect a console directly onto this standby supervisor card and get any information at all - for example to fi...
Hi.....The shown logging messages is my CMTS Router.What happen ? Do you know this messages ? ---------------------------------------Apr 23 02:03:50: %UBR7200-5-UNREGSIDTIMEOUT: CMTS deleted unregistered Cable Modem 0030.eb85.b201--------------------...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM | ||
11-08-2023 03:38 AM |