Hello,I upgrade the Broadband system, include SCE 2020, CM and SCA BB from 3.0.6 to 3.6.5.The issue is I when open SCA BB with the configuration file create in 3.0.6, I can´t make any change in the rule.The only way to make modification is open the S...
Hi,We have SCE 2000 3.5.5.I have a problem to capture some snmp traffic.From a server To a router, our SCE captures traffic snmp "GET-NEXT-REQUEST". I can see these traffic in RDR (Transaction RDR and Subscriber RDR).but, From the same server To the ...
HiHow can i change the boot device on IOS XR ???RP/0/5/CPU0:-12406#sho ver | in Boot deviceBoot device on node 0/1/CPU0 is mem:Boot device on node 0/3/CPU0 is mem:Boot device on node 0/4/CPU0 is disk0:Boot device on node 0/5/CPU0 is disk0:Thx
Hi there.Mi name is Kristian.Recently i am configured a UBR10k to give to the clients public ip´s and for the cm private ip´s.The configuration is the following:interface Bundle80 no ip address cable arp filter request-send 3 2 cable arp filter rep...
Hi, I m trying to achieve redundancy for gateway of pppoe adsl clients on LNS. My scenario is as below.> Telco LAC sends the PPPOE session to our LNS using L2TP to LNS. It sends it to Primary LNS at all the time till the Primary LNS is alive.> If pri...
Hi.In a SCE2020 with version 3.5.5, we have can not establish more than 10 simultaneous connections. We obtain a message 'unable to open connections - max number of sessions exceeded'.We use the SCE API for connect to the SCE.Is limited the SCE to 10...
We need to estimate the length (bytes) of RDRs generated by SCE.In particular we are interested in the following RDR types:- HTTP Transaction Usage RDR- Transaction Usage RDR- Subscriber Usage RDRAny suggestion is appreciated.Thanks,Marco and Fabrizi...
Helllo ...I have the following IOS:Cisco IOS Software, 7200 Software (C7200P-IPBASE-M), Version 12.4(4)XD3, RELEASE SOFTWARE (fc2)BOOTLDR: Cisco IOS Software, 7200 Software (C7200P-KBOOT-M), Version 12.4(4)XD2(1) I can not use - no such command - ven...
Hi,I am configuring staic L2TPv3 on Cisco 881. According to the feature navigator it is supported and I can configure without any problem. The L2TPv3 session seems to be UP but apparently there is no data I can send accross this L2TPv3 tunnel.Anyone ...
I saw in the System Configuration Management Guide for ASR 9000 the following:Specifies the scale profile for the router.default—efficient for deployments that require large Layer 2 MAC tables (up to 512,000 entries) and a relatively small number of ...
Hi,I´m trying to implement a SCA solution. In this scenario I need to integrate Subscriber Manager with ACS (Radius Accouting) and I want to know if this integration is possible.Regards,Jaime.
Hi AllI have a question here, I'm now analyzing the subscriber hourly usage volume per hour. As I know, the data Top Subscriber Report in the BB Console is collected by Topper/Aggregator (TA) Adapter inside the Collection Manager (CM) server. Could a...
Hi AllI'm just studying how to implement the multiple thresholds of subscriber quota on my network. I'm generating the report on subscriber average consumption as below to determine what is the right value of quota to be set for each of my subscriber...
Hi all,I am trying to assign the ip address to pppoe client using Radius. The scenario is basically we will have pppoe clients (Not Cisco AFAIK) and they will authenticated against FreeRadius from LNS. I tried to find out some documentation about it ...
