Hello,We have Cisco ASR 1002-HX and we will use just 4 x 10G ports do we need to have any special license for those ports? Also, we didn't see any option to change the system throughput to 20G it's not clear to us what kind of system throughput we c...
Forum Posts
Hello,I have an 819G-4G router with IOS c800-universalk9-mz.SPA.159-3.M7.bin.If I use a SIM card without a PIN code I cannot establish a connection :Router#sh cellular 0 securityActive SIM = 0SIM switchover attempts = 0Card Holder Verification (CHV1)...
Hello, everyone! I've always been told that the routing table is a control plane concept. You build this table, collect the routes, the way they were learned, their metrics, and so on. You then use this information to build a more forwarding-suitable...
Dear Sir, If I have the below scenario: 1- Two routers facing the internet each of them is connected to different ISP. 2- both routers should provide HA in configuration. 3- Internet Firewalls will be configured in (Active/Standby). 4- hav...
This is my router config: interface GigabitEthernet0/0.168description Security Deskencapsulation dot1Q 168ip address 192.168.0.1 255.255.255.0ip flow ingressip flow egressip nat insideip virtual-reassembly in ip nat inside source route-map SECURITY_D...
We are encountering an issue with setting up OSPF routing on two Nexus9000 switches we recently put into service.We have several branch locations in our network. Each has its own branch router or L3 device. These devices use OSPF to form neighbor rel...
Hi I have the following topology in GNS3: Currently only concerned with R1/2/3 which are all in area 0, I have created static routes on R1 as below:ip route 77.1.0.0 255.255.255.0 66.1.1.2ip route 77.1.1.0 255.255.255.0 66.1.1.2ip route 77.1.2.0 255....
Hello. I am using 2911 router on PKT and tried to use police to use Copp but there is no command, is it not possible to use CoPP on PKT?
HiI have a Router where we peer with Service Provider using BGP, is it possible to add extra VRFs to our Network without using a BGP peering can I have static VRF set up and leave the existing BGP peering for our staff Networks as is, if so what is t...
Team,I need your help for BGP prefix-list/route policy Config.We currently have a static route with the ISP for both the primary and secondary connection.We are now going to make it BGP.For simplicity, I have attached a photo of the basic connection ...
Hello,I have topology as below picture where i have 4 location connected over WAN. Every sites have dual WAN and use OSPF for routing protocol and divided into 4 OSPF area, also we define the OSPF as point to point in the config.With this topology i ...
Closed. This question is off-topic. It is not currently accepting answers. NE is a site for to ask and provide answers about professionally managed networks in a business environment. Your question falls outside the areas our community decided are on...
Hello!Can you please help me, I'm new to VOIP:We have Cisco CUCM version 12.5.1 with 7960 and 7911 phones. How can I see missed calls on the phone if the line is busy (talking with someone)?SO called person is talking when I call him, the phone rings...
I have a scenario where I have anyconnect vpns terminating to a Cisco FTD (configured with FMC). There are multiple connection profiles, that have separate ip pools, which then enter a catalyst 9500 L3 switch (main router) with multiple vrfs. I wou...
Hi, I have received Cisco VXR 7206 that can’t boot and always goes to ROMMON.After debugging I saw that the router does not have valid IOS that can boot from.rommon 11 > devDevices in device table: id namebootflash: boot flash ...
