Hi GuysHow could i connect a Branch site back to HQ using a ADSL Line , over the Internet , asa far as i knowwith ADSL they dont give Real Public IPThanks allIbrahim
Forum Posts
Hi Cisco Gurus, I have a bit of a dilemma here I hope someone can provide some guidance on. Essentially we have remotes that have two hubs and are multihomed with MPLS primary and VPN backup. The Western remotes primarily go to the Western hub wi...
Resolved! clarifications on item in quotation
CAN I ASK CLARIFICATIONS ABOUT THE BOLD LINE , what is that mean? is it warranty or what ? CORE SWITCH WS-C3850-48F-S Cisco Catalyst 3850 48 Port Full PoE IP Base CON-SNT-WSC388FS SNTC-8X5XNBD Cisco Catalyst 3850 48 Port Full PoE IP S38...
Hi Team, When i am trying to get the mstp port state with SNMP MIB i am not getting output. anyone can help here. My switch model:CISCO 4500X
I have the following topology below, in GNS3. Basically, the cloud NAT-1 is the Internet, R1 is my border router with NAT and FWASAv-1 was supposed to be able to access the Internet, but can't. I created that other leg with R2 to test the NAT, and to...
Hello all, Trying to get this 4G router up and running but its not going well. I used CCP Exress to set it up and it works for the most part but only on EDGE(1X) and 3G at extremely slow speeds. It never negotiates its way to 4G and if manually set...
Resolved! When do we implement Static Routing
Hello,A newbie here. I have tried to search in google on this but I cannot find the answer to my question.I hope you can help me and shed some light. Your expert advise will be of great help here's my question:1. When do we implement static routing? ...
Hello All We have a switch stack that we connected too for the first time via console connection and they are stuck with justa ^> prompt Tried to get into enable mode but normal cisco cisco123 passwords do not work. Any suggestions? As we are not i...
Hello community good morning, We are experiencing troubles with one BVI in our ASR 9006 (IOS version 6.0.2), the BVI is the gateway for a customer and yesterday it didn't work and also generates this log: LC/0/1/CPU0:Apr 4 12:58:35.419 : fib_mgr[...
Hi All We use Cisco 887VA routers for ADSL, I believe the throughput from the Cisco specs says it is sized for up to 15Mbit If this is the case, what router would I use for some fiber broadband 50Mbit etc cheers
Hi there! I am experiencing a problem which I suspect involves an issue with route advertisement. The setup is as follows: Device A 10.0.154.2/25 gateway 10.0.154.1 Router A interface 1 10.0.154.1/25 interface 2 10.0.154.250/29 interfac...
When I enter the command show ip route I dont get the cost by route. What command should be used to obtain route cost? Thanks, Martin
I'm having some problems with my Cisco RV320 Dual Wan, I'm trying to make a forward to my server in port 8080, but some computers can't access external, example: my home computer can access the page with :8080, but my boss can't access with his compu...
Hello, I'm hoping that someone will help me. I'm setting up my 2929 router to use the cellular interface as a backup for my Comcast business internet. I tried a bunch of different ways but the cellular connection keeps flapping and resetting. Below i...
we would like to perform load balance in edge routers connected to same ISP. the edge routers are running IBGP between them using IGP protocols as OSPF. the Edge routers connected to ISP are running EBGP. i am trying to follow the example i...
