Hola. Buenas tardes, alguien sabe Cual es throughput del equipo IR1101
Forum Posts
hello guys,Newbie here. I have been trying static routing for my lab and I'm unable to establish communication b/w computers connected to different routers. i have established routes for both the routers and they are showing up in the routing table b...
R1---R2 is running with ibgp .I checked the configuration like AS number , MTU as well MSS setting on both side . looks good and symmetric .both side MTU is 1500 bytes . we have set the MSS as 1460 bytes also on both side .what should be the possible...
Resolved! Issue with HSRP Preemption
Hi, I am using HSRP in my lab with a default priority. But, having issue whenever my active router goes down, and later when it comes up then it is continuing with standby status not the active. I enabled Preemption that is also not working. when my ...
Hi. I'm trying to setup Cisco 897-K9 for my VDSL internet connection with dynamic IP (if I will successful then I’ll order a /29 IP prefix). I was checking different configurations but no of them work. Some people say I need to put for interface ATM...
Resolved! iBGP advertisements
Hello,I'm having a problem trying to advertise from one bgp AS to two other routers with different bgp AS. if you see the image below, R2 is on AS 64520 and R1 and R3 are in AS 64550. I'm starting with BGP and I am stuck on this, for some reason...
what is loading ,route tag ,reliability,TAG in below--- AAA#sh ip route x.x.x.xRouting entry for x.x.x.x/25Known via "eigrp 100", distance 170, metric 2688256Tag 65207, type externalRedistributing via eigrp 100Last update from XXXXXXX on TunnelXXXXXX...
Good afternoon everyone, my organization has added a Branch Office.I wish to have all of the internet traffic for the Branch Office flow through the HQ NAT Router. I have set up a working DMVPN with dynamic routing using eigrp (see the attached image...
Hi All, I'm running a 4331 with isr4300-universalk9.16.09.05.SPA.bin code. Get a feature error/warning when applying "service-policy output TRAFFIC-OUT-POLICY" on a Dialer interface. Is this a code feature limitation? Priority feature is not support...
Hi, I have just had an issue with one of my core routers. An ASR 1001-HX that gave me a kernel error and restarted. I had the following LACP configuration: R2#show etherchan summ Flags: D - down P/bndl - bundled in port-channel I - st...
Resolved! Rommon mode - Router 3945
Hi, my router is currently stuck in rommon mode.Are there any helpful commands out there that will help me understand why my router is stuck in rommon mode?Is there anything I can test/try to get out of rommon mode?If need more information please rep...
I'm completely new to ACLs, so I apologize if the solution is obvious.I attached the packet tracer project, I'm trying to set up some ACLs on the core switches to manage inter-VLAN routing and VLAN access to the "WAN".For now I have applied the follo...
Resolved! OSPF Routing -Designator ID
Hi, I have done OSPF lab. In that I have noticed OSPF Designated ID in every Ethernet link is confusing about selection. The selection Process is based on Priority or Router ID. "OSPF deems a router more preferable if the priority for the interfa...
please Help to find the throughput value of ,Cisco1950BR-SEC/K9, C891F-K9 routers
Resolved! Leaking global connected route to vrf
This is my first entry into VRFs. I have been asked to separate each user section by floor and separate VLANs. The printers VLAN is separated as well for security and control as defined by business rules. I have a 3850 (stackwise virtual) acting as...
