Resolved! Intervlan Routing in Cisco C9300 switch
Hi, I want to enable the intervlan routing in Cisco C9300 switch. Does IP routing command is enough to do this or more config I have to do?
Forum Posts
Hello, I have this network where D1, D2 and D3 routers are configured as iBGP. Network works just fine until I do the command: neighbor x.x.x.x update-source loopback 0 on each router. Once this is done, routers begin to shutdown their neighbors af...
Resolved! Smart Link Backup RV042G
Hello , I am writing to inquire about the feasibility of setting up a backup IPSEC VPN tunnel using WAN2 on two RV042G routers. Currently, these routers are communicating via an IPSEC VPN tunnel established over WAN1. However, our client is interest...
Resolved! E1 TO ETHERNET CONVERSION
Help me to know What exactly E1 and How it differs from Ethernet and also how we can convert E1 to Ethernet
Hi All, I am a little bit confused while configuring below commands in HSRP. track 10 interface G0/0 line-protocoldelay up 10 delay down 20Can anybody make me understand what the meaning this is.Only confusion is in delay up and delay down. Also...
I have 3 spoke and 2 HUB and one spoke has no issue with internet and 2 spoke has slowness issue so Can we clear DMVPN session?will it affect the session and will it be reestablished after clear session?
Hello,We're relatively new to the world of MPLS and have been working on a testing environment using ASR routers. In this setup, we have two clients, A and B, with an MPLS L2VPN configuration.In our test, scenario 1, both Client A and B have two site...
Resolved! Configuring OSPF on sub-interfaces
Greetings everyone, I'm seeking clarification on the functioning of OSPF in relation to sub-interfaces within a single router. In my current setup, the physical interfaces are associated with the 192.168.1.0/24 network, while the sub-interfaces fall ...
I have MX 450 connected to a switch port and the switch is connected to a router. The router has 3 interfaces, 2 MPLS and one local internet connection. for now, my Meraki traffic goes via the MPLS circuits cross to the DC. The configuration on the r...
Hi, I'm trying to complete daily labs in packet tracer now that I've switched to online school. I'm want to have Router0 be connected to two other routers as well as a switch (3 devices), but only 2 Gig interfaces show up when trying to connect with ...
I have two C9300s acting as Core Routers for my Site, with multiple VRFs. I'm migrating routing from OSPF to BGP, with OSPF acting as the Underlay for a VRF and BGP performing inter-VRF routing, between the two Cores, a Palo FW, and a Cisco SDWAN rou...
Hello, Is there any way to disable the blue LED on the front cover of the new 1100 series routers? Can't find anything in the 1100 series software configuration guide about it. Specifically in this case I have a C1111-8P but the other models also...
Hey guys.I need help configuring a Cisco 899G-LTE for two incoming internet connections. 1st VIVO Fiber (Primary)A network cable will come out of the modem and connect to the WAN interface of the 899G-LTE router (GigabitEthernet9) Local IPv4 address:...
Hi,10.0.0.0/11Site 1:- 10.0.0.0/12- Divided further into /16: 10.0.0.0/16, 10.0.1.0/16- The first /16 is dedicated for management.- Starting from the second /16 for data: 10.1.0.0/16- Switch 1 VLAN 10: 10.1.0.0/24- Switch 2 VLAN 10: 10.1.1.0/24- Swit...
Resolved! VTP BETWEEN SWITCH AND ROUTER
Hi everyone, I'm a beginner and just started my diploma in IT. I'm currently stuck on this question, switch 3 is the VTP server and the rest of the switches are clients, I've already configured them as clients and server with the same domain name. I...
| User | Count |
|---|---|
| 17 | |
| 9 | |
| 8 | |
| 7 | |
| 6 |
