Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Please help to split traffic

Hi. we have two 2821 cisco routers. they has interconnection, and ISP providers connected to each of them. Take a look attached picture.Our ISP2 says that we can use IP address 3.3.3.2 for our own purposes. And we want to use this 3.3.3.2 for WiFi ne...

ASR1002 SFP-GE-T not operational

Hi,We have a Cisco ASR1002 with RP1 router with 4 built-in SFP slots. When we insert an SFP (SFP-GE-T or GLC-SX-MM) into any of the build-in slots, the link fails to become active. The LEDs are amber in color and show facility status shows the Ethern...

fsebera by • Level 4
  • 880 Views
  • 0 replies
  • 0 Helpful votes

Resolved! 2621XM encapsulation question

while back I configure one of my cisco router on the stick, I remember getting the info over the net; and before I was a ble to  config the subint to an encapsulation I had to enable a command on the router, I did a mem erase on the unit, so now I ne...

Resolved! Needed help on QoS - urgent

Hi there,I encounter 1 problem. Customer need to set the bandwidth for business class to have a 512k of speed and i already set it with "bandwidth" conmand.What if they want it to ensure if the bandwidth exceeded 512k it will remark it to have IPP=0H...

BGP redundancy... and dual ISP links on each router

Hello,I have small topology like this :                    /--(Ge0/0.10)-- ISP 1(Ge0/1) Router A ---                    \--(Ge0/0.20)-- ISP 2 I want to redundant router A with another router. A current pratice is to use HSRP vith an iBGP session like...

jquintard by • Level 1
  • 2997 Views
  • 9 replies
  • 0 Helpful votes

Resolved! Help with multicast setup

Hi, I`m attempting to set up a multicast in ouer network.The multicast is provided by a IPTV provider.Uplink from service provider is located at site A.My RP is set up at site B.From site A to B I have set up a VLAN (VLAN 400) to link the IPTV provid...

perpaal by • Level 1
  • 1561 Views
  • 8 replies
  • 0 Helpful votes

Resolved! Unable To Ping across subinterface on 1941w

I am currently working on a 1941w router. The problem that I am having is that I am unable to ping the switch that is directly connected to it and I am unable to ping from the switch to the router. If I take the address off of vlan 1 and move it to g...

ATM problem with various models

Hi everyone,I'm having a problem with various Cisco ADSL modems and one specific ISP. The ISP is changing their ATM network to Ethernet and ever since the Cisco routers regularly lose their connection. Only resetting the modem brings the line back. A...

3G router configuration

May I ask the commandchat-script <script name> "" "ATDT*98*<profile number>#" TIMEOUT <timeout value> CONNECTWhat is the defference between ATDT*98* and ATDT*99*and profile settingcellular 0 gsm profile create 4 APN.telstra pap john@doe.com johnpassw...

Resolved! Cisco NM-1CE1T1-PRI module

Hi!!I have checked on Cisco.com and as per a module support document for ISR's G2, the NM-1CE1TI-PRI module is not supported on new ISR's.Grateful if more clarification could be obtained about the above.Will be router not detect the module when inser...

net buzz by • Level 1
  • 642 Views
  • 2 replies
  • 0 Helpful votes
Load more