Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Labels

Forum Posts

Start a conversation

Resolved! Disaster Recovery - Redundant VPN Tunnels

Hello all, thanks in advance for your expertise.We are setting up a disaster recovery site which will host redundant copies of our servers and critical data in Kansas City.  In the case of a disaster, our headquarters site would be totally gone.  Cur...

SPAN Problems on Cisco 871

Hi - I am having some problems creating a SPAN port on my Cisco 871 (running IOS 12.4-11T).  My 871 is connected to a DSL modem, and uses "IP Negotiated" to get its dynamic ip address.  I want to monitor the WAN port (FastEthernet4) using SPAN, but w...

boeckelr by • Level 1
  • 2076 Views
  • 4 replies
  • 0 Helpful votes

nat or pat, which comes first?

All,I have the following configuration on my ASA:nat (inside) 1 0.0.0.0 0.0.0.0global (outside) 1 192.168.1.10-192.168.1.19I have multiple /24 internal networks. My questions is, when traffic exits from inside to outside, which will come first? NAT o...

yuhuiyao by • Level 1
  • 711 Views
  • 1 replies
  • 0 Helpful votes

Resolved! c887 15.1(3)T IPV6CP? failure in PPPoA

My ISP is *starting* to roll out native-v6, quiet-like, and I'm trying to get it running in the ADSL-connected home-lab.However, for some reason, PPP link setup fails for v6; v4 is fine, as always. The argument which seems to be sent from IPV6CP as t...

Resolved! 2901 VWIC card issue

I added a VWIC2 1MFT-T1/E1 card to my 2901 router.  There were two in it already, and I need to add a 3rd circuit.  After installing the card, the boot process sees the new card, but once it is completely booted, the new card is nowhere to be found. ...

jlmickens by • Level 1
  • 2176 Views
  • 2 replies
  • 0 Helpful votes

How to route a segmented LAN?

I had posted previously about segmenting LAN traffic (  https://supportforums.cisco.com/message/3393501#3393501 ) and have a  follow-up question. The traffic flow on the network is fine, but we are not able to access our remote locations.Using the ex...

Add command to persistent db failed. File system full

Hi,I'm using persistent logging and getting the file system full error message, but I don't see where I'm anywhere near fullHere's the relevant configution detail...archive log config  logging enable  logging persistent auto  notify syslog contenttyp...

lcaruso by • Level 6
  • 979 Views
  • 3 replies
  • 0 Helpful votes

Resolved! OSPF reconvergence after fail over

I am implementing a solution for for a customer that has dual WAN links for redundancy. In order to achieve this (and for security purposes) I have implemented 2 OSPF processes (one of which is a on a VRF).The subnet that I am testing for fail over i...

Resolved! EIGRP offset-list

Hi Guys i have the concept of off-set list but getting confused abt in and outfor exampleif i have an off-set :router eigrp 1offset list 1 out 1000 interface ethernet 1/0Access-list 1 permit 10.0.0.0/24so what will it do and if i type offset-list 1 i...

Resolved! Cisco Live Virtual

Michael Kowal conducted "Enterprise Multi-Homed Internet Edge Architectures" BRKRST-2044 at Cisco Live Virtual.He said the pdf would be his whole package, but the link for the virtual class download is just the limited presentation he did at Cisco Li...

WAN bandwidth upgrade

Hi,I need to study the possibility of WAN bandwidth upgrade on our HQ.Do you have any suggestions as to how to analyze existing bandwidth usage, and if bandwidth upgrade is necessary? do you have any document/link you suggest to me?thanks

Load more