Buy or Renew
Buy or Renew
NOTICE: The community will be in READ-ONLY Sept. 6 – 9 to add Umbrella release notes and announcements. Learn more.

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

“Webinar

 
Labels

Forum Posts

Start a conversation

packet droping inside LLQ

Hello,I have the following policy-map configured on the serial interface:policy-map VOICE_UP  class VOICE   priority 26  class TELEMETRY   priority 110  class USER1   shape average 1536000   bandwidth 670  class USER2   shape average 1536000   bandwi...

jouk by • Level 1
  • 728 Views
  • 3 replies
  • 0 Helpful votes

Qos help

Hello all,I have 2 branch locations connected to HeadOffice through MPLS VPN,HO Router has one connection to internet and one connection to the MPLS cloud,The Br Off accessing internet through HO,Head office connection to MPLS clould is 1MBr office C...

Resolved! 2821 VWIC 2MFT-T1 installation

I had to dig this stuff out of storage and cobble together a router on short notice. I installed this WIC into a 2821 and I can see it when I do a show ver.Cisco 2821 (revision 53.51) with 249856K/12288K bytes of memory.Processor board ID FTX1006C0P3...

rshum by • Level 1
  • 914 Views
  • 2 replies
  • 0 Helpful votes

VOIP config for 1841

Hi,One of our clients have plans to use VOIP. Since we only manage their 1841 routers I've been issued the following parameters-DIFFSERV/TOS PARAMETERS                  RTCP Reporting  Enabled? yCall Control PHB Value: 46      RTCP MONITOR SERVER  PA...

Resolved! 2811, High CPU load and occasional crash. HELP.

2811 routerCisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9_IVS_LI-M), Version 12.4(24)T4, RELEASE SOFTWARE (fc2)CPU utilization for five seconds: 82%/73%; one minute: 74%; five minutes: 77% PID Runtime(ms)     Invoked      uSecs   5Sec   1...

Resolved! Extended LAN over Frame Relay

Greetings to everybody.I've always configured point-to-point Frame Relay in a way that connects two different lan segments and using static routes to reach each of these networks.One of the client is moving from one location to another, but he is lea...

3560 in CCIE R&S Lab exam

Hi,Why need the Cisco Catalyst Switches 3560 in CCIE R&S Lab exam, is not Cisco Catalyst Switches 3550 enough? What kind of commands that support by 3560 and not supported by 3550.

Cisco 2921 maximum Number of L3 Ethernet Ports

I am currios about one thing with the Cisco 29xx routers.How many routed ethernet ports do they support when using HWIC-1FE and HWIC-2FE modules?On the Cisco site for the two interface modules and in the corrseponding PDF of supported interfaces for ...

BGP multihoming with Redundant routers

Hi,I have two perimeter routers connected with two different ISPs . I have my own BGP AS number and public ip pool. I want to run BGP Multihoming with redundant routers. so that I can load balance my inernal traffic with two different ISPs. Kindly sh...

Resolved! access list issue and ip route

HiHave cisco router 1921 and 3 cisco switch 3560Gi want to configure the cisco router so as network 192.168.4.0/26,192.168.3.0/26,192.168.2.0/26, all to access internetR1921(config)# ip nat inside source list 102 int G0/0 overloadR1921(config)# acces...

Odd issue - can't ping within LAN

Hi all,I haven't come across this before and have been scratching my head about it for the last few hours and need a second (or third or fourth!) pair of eyes here.I have an ASA5510 at the network edge, an inside interface of 10.1.0.x, a dmz interfac...

View All
Unanswered Topics
View All
Review Cisco Networking for a $25 gift card