Routing

Having troubles with static routes and dialer interface. I have a 3745 that has two bri's tied together w/a dialer. I have a satellite connected to the an ethernet on the router. What I want to happen is the following:If there is a local cable cut...

I am trying to throttle all http traffic to a fixed rate (512K) and can't seem to make it workrate-limit input access-group 101 512000 512000 512000 conform-action transmit exceed-action dropaccess-list 101 permit tcp any any eq wwwaccess-list 101 pe...

i have got 2950-24T, i wanted to restrict only MAC address to use the fas 0/1 port, if some other MAC address NIC is connected it should not allow is it possible? i tried the following options but couldn't suceed.interface fas 0/1switchport mode acce...

Dear Sir, We have 3 ISP Connectivity’s .Two links are terminated in one router and other link is terminated I another router.DETAILSISP NAME BANDWITH ROUTER1.VSNL 2 MBPS CISCO 2621XM2.RELIANCE 4 MBPS SAME ROUTER 1...

This is the basic layout of my networkCPS------192.168.0.10Host | |CPS------Fa0 int 192.168.0.4Router---S0 int 192.168.100.1 | |JCWA-----S1 int 192.168.100.4Router---S0 int 192.168.101.4 |-------fa0 10.6.18.4--host 10.6.18.10 | |CPTC-----S0 int 192.1...

Hi,Pls find the network diagram attached along with the mail. In this diagram we can see one router connected to internet and also connected by 2 leased lines to a different branch. I want to do load balancing on these two links (not static load bala...

Hi..Understand that L2 Ether channel can use src/dst mac/ip/port to load balance across a L2 channel.Any idea for L3 Ether Channel in GSR, what kind of load balancing technique (load balanced using src/dst ip/port? )is used ?ThanksEng Wee

I have a few sites I can't seem to access on the internet. It's very consistent with these sites I can traceroute to them from my external routers but not from my internal devices that sit inside a Pix firewall. Has anyone ever run into this before? ...

hi, I found a tcl script in cisco as below. how to use it.best regards.fred.#### Place required comments here!!!##package provide sendmail 2.0# Sendmail procedure for Supportnamespace eval ::sendmail { namespace export initialize configure sendm...

Hi all - I have a pretty basic WAN - 7 sites\T1's & igrp for routing. I have purchased a new 2821 to replace an aging 2503 and found that the IOS that came with does not support igrp, but it does support eigrp - the version is: C2800NM-IPBASE-M), Ve...

How do you clear the counters on a T3 controller in a 3660 without rebooting or taking the circuit down?

Hi All, i am having high cpu usgae problem with my Cisco 2621 Router. Router have 1 FE, 2 WIC2T interfaces. On the WIC, 2 of them are working as connections to ISP ( 2Mbps each) while another WIC is designated for 512Kbps VPN. Last week while the to...

We have upgraded our UBR 10K from 2x8 line cards to 5x20 line cards. After the upgrade all ports reported a drop of 5bd, but we have verified that these are invalid reports. Have you heard of this issue? I show no known bugs on Cisco's site, maybe...

We are trying to fine toon our QOS policies and in doing so we are lowering the tx-ring-limit on each of our pvc's.When I lower it to 3 some of the branch locations loose connection back to the main router.The configs on both ends are exactly the sam...

Hi,Imagine if you will a head office and a remote site. Interconnecting the two sites are 2 WAN link's provided by 2 independent ISP's. Each running BGP on there internal networks. At each site there is a 3550 Layer 3 switch. This is acting as the ac...