Hello, I have a small problem with the Nexus 5548UP.Have created vlan's and the vlan interfaces.I can ping the interfaces. Works.Ping from windows host to all vlan interfaces Works.Pinging from windows host in vlan 10 to windows host in vlan 20 does ...
Forum Posts
I have a Cisco ISR 4331 and I have setup 2 internet connections with 2 WANs. When both ISPs are working, the connection works just fine, the load is balanced between the two. When one ISP fails, half DHCP clients stop working, obviously. My default r...
Resolved! no EIGRP neighship is being formed.
Hello EXPERTS, I have configured EIGRP 100 on HEAD-OFFICE and BRANCH-1 but no neighborship is formed. OR i haven't understood the routing properly, if so, please make me clear. I will be very thankful to you guys!!. Topology is attached below. no a...
Resolved! BGP network without mask
Hello,I just added a public X.X.X.0/24 ip block on our BGP routers... I have 3 routers BGP on AS 1234 with an IGP. router bgp 1234address-family ipv4network A.A.A.0 mask 255.255.255.0network B.B.B.0 mask 255.255.252.0network X.X.X.0 The subnet mask i...
Resolved! Cisco 3850 ip Nat
Good daycan I do the IP nat on cisco 3850? Please advise me thanks Vlan 10192.168.1.1Vlan 2192.168.2.1 access-list 102 permit tcp host 192.168.2.169 192.168.1.169 0.0.0.255ip nat inside source list 102 interface Vlan 10 overload_________________ cisc...
Hi all I am new to EBGP and is task to do some immediate setup Not asking for direct answers but rather hope gurus here be able to confirm my understanding and provide some suggestions to avoid any rookie mistake i might make R10 are connected to R1-...
Hi all,I apply QOS setting in the GRE tunnel, it is normal after i apply the QOS setting Three day later, We have many packet loss of ping 8.8.8.8. We got the error in the router. Please find the below message. The error messageJan 7 11:49:36.193: %L...
Hello Regards to the command "show ip nat statistics" on an ASR1000. The increment of the counters "In-to-out drops", "Out-to-in drops" and "Port block alloc fail:" are refered to a PAT problems? Or just are packets that don´t need to do nat? This...
Resolved! Setting up WAN Access in Cisco 891F
Hi Everyone, I have a Cisco 891F router that I got second-hand for a lab environment that I am trying to setup. I managed to reset it, gain access to the router, and set some things up, but I am unable to get access to the internet from a computer co...
Hi all,I have a question similar to another I asked previously. I'm wondering what strategy would be used to simulate traffic flowing through an ISP router in packet tracer. Both ASAs have dynamic NAT enabled and can ping each other as they have rout...
I have a network i'm practicing on consisting of an ASA, two routers, two switches, and two hosts. I have configured dynamic NAT on the ASA. I can ping PC1 from R1 but if I try to ping PC1 from PC0 it doesn't go through. While looking at the simula...
Hi everyone,Wish you have anice day!I have a lab as picture below. The lab request R5 just learn 1 row route 10.0.0.0/8 from ABR R1. How can I summary on R1 all subnets 10.0.0.0/8 behind it, I try configure on R1(config-router)#area 0 range 10.0.0.0 ...
Resolved! Defaut route and track
Hi guys need to check my sanity - I'm pretty sure i have this right I've got quite a simple set up R4 has 2 default routes using the track command to favour 192.168.0.1 as the default gateway : interface FastEthernet0/0ip address 192.168.0.2 ...
Resolved! ASR 903 Error log
Hi I have an ASR 903 RSP3. when it tries to boot up, the following log appears on the console: Image loadedBoot image size = 518430927 (0x1ee6a0cf) bytesI2C Bus busy, please check the BP IDPROMget_mac_addr: Couldn't find a valid macaddrI2C Bus busy...
Resolved! PBR and VTI IPSEC
Hi we are trying to configure PBR with VTI as next-hop interface or ip address, but with no luck. we see that traffic is matching the PBR and ACL and indeed the traffic is returned according to the statistics of show crypto ipse sa peer x.x.x.x but...
