Routing

Hi, I know by default the vlan 1002 is used for FDDI. Of couse my 3550 do not have fiber ring interface.So how to use this vlan for ethernet ?S1#sh vlan briefVLAN Name Status Ports---- -------------------------------- -...

hi,I tried to encapsulate a subinterface on a Layer 3 interface ( no switchport ) on Catalyst 3550 but there was no option for encapsulation dot1q <vlan number> command?When I try to add a IP address on that subinterface it notifies me that :Configur...

Hi all,I have a 3745 router with dual power supplies and I'd like to connect these two two independent power sources. Our facility can only provide out-of-phase independent power, i.e. there is a phase difference of 120degrees between the two power ...

Here is the PNNI topology from one of the ASP:USKEN15DRASP#sh atm pnni topology node 13Node 13 (name: USUNI13DRASP, type: LS1015, ios-version: 12.0)Node ID..: 56:160:47.009181000000009086003401.009086003401.00Node AESA: 47.00918100000000908600...

Could anyone tell me the correct command line to add a port range 16384 to 20384 in addition to my existing ports?Currently I use the following:ip nat inside source list 1 interface Dialer1 overloadip nat inside source static tcp 192.168.2.1 80 inter...

Here is issue, I have a 3662 router with 2 2FE-2w and a PRI 1CT-CSU. One of hte 2FE-2W has 2 1DSU-T1 v2 Wic and the other has 1 1DSU-T1 v2 wic and 1 Vwic-1MFT-T1. the 3662 has a AIM-ATM module installed in it.My problem is the IOS sees the PRI an...

I'm trying to connect two routers (7206 and 2600) via a serial interface over IP. Currently the serial communicates perfectly via IPX. I've just confgured ip addresses on both sides with a /30 mask and encapsulation is PPP but they cannot ping each o...

I am trying to add a COX fiber connection to route via 3660. Have tried to connect it via a cross over cable to a Cisco 3500 switch port. The address of the switch and 3660 is 10.254.1.X and the tera wave traffic will be 10.5.196.X.

hi,Actually this has been used with distribute list as: distribute-list 1 out s0/0 access-list 1 permit 0.0.0.0 access-list 1 deny any. couldnt make out..kindly help ..

hi,kindly guide me the meaning for this :access-list 90 permit 0.0.0.0access-list 90 deny anyRegards,

Trying to save money I ordered a cisco1841 router with out any T1 wic cards since the 1841 was replacing two 1602 routers that already had wic 1dsu t1 cards. When I boot the 1841 router I get the following erroe:*Aug 26 16:14:11.831: %CFG-3-CARD_NOT...

Hii all,I want to Monitor CPU, Memory & Bandwidt Utilization on my Routers. I also want to get Notification for the same on my Mail. Is there any freeware software for this. also tell me the configuration part.Thanks.Anis

I seem to be having some problems with my 1721. For some reason after a while the internet cuts off and the whole network looses internet. And the only way to get the net back is to restart the cable modem. The time between it cutting off is random, ...

Hi allLet's say I enable EIGRP on my router with router eigrp 900network 10.0.0.0no auto summarythe router has 5 WAN interfaces with IP addresses coresponding to subnets of 172.26.1.0/24 using 30 bits for masking.The two ethernet interfaces have IP a...