In my L3# Switch I have a default route pointing to internet.ex: 0.0.0.0 0.0.0.0 next hop<x.x.x.x> So by default for any traffic not in the routing table, it will follow the default route.But would like to know , whether the static/default route can ...
Forum Posts
I have two edge routers on my enterprise network that are both receiving a default route via BGP with my ISP. I want to be able to redistribute the default routes into my internal network, but preferring one over the other. I'm doing OSPF on these ro...
Hello everybody,I have the following topology. Network A needs to talk to Network B.I created Customer VRF on the middle PE (PE-X) and I successfully saw the routes from both sides, however Network A still cannot ping network B. also, traceroute show...
Dear all, I appreciate if you can let me know your feedback, in my opinion actually Cat3K can support limited layer 3 static routingon Stackwise with LAN base feature right? however if I have been investigating with CCO there is following information...
Resolved! Connect different networks with RIP
Hey, My project contains five different networks and my task is to connect them via RIP. Each network has a PC connected to it. My goal is to be able to ping every PC from each PC. I've already tried to add the different network addresses to Router ...
Hi Guys, If anyone can explain this, in brief, would be really appreciated. Question :Company A is running BGP to connect to external peers they were recently acquired and new peers(Company B) will be connecting using the acquiring company(Company A)...
Hi guys, This is one of the question I had on a paper. Can anyone explain the answer to this question briefly? Question: When configuring an aggregate address with BGP, What addition to the aggregate-address configuration is needed to only advertise ...
So, I know in the later released of IOS XE 16.8.x the default has been raised for IPSec throughput. But for people running IOS XE code before that, I would like some help in verifying IPSec Aggragate Throughput. From my understand, If I have a ISR 4k...
I have a c9300 in use as a router. We have inter vlan routing and source based policy based routing.When we try to go to addresses that do not have a route in place for, the mgmt page for the c9300 comes up. I have not been able to find anything rel...
Resolved! Static Route - Unable to add to router
Hello, I have 3 routers connected on which I ran IP OSPF 1 Area 0 command and they all worked fine as I am able to ping from each computer connected to the router through a Switch. I decided to removed OSPF from all interfaces using NO IP OSPF comma...
Regarding the post "Definition Of Feasible Distance In EIGRP Convergence":https://community.cisco.com/t5/routing/definition-of-feasible-distance-in-eigrp-convergence/m-p/4087265#M334424Peter Paluch's (Hall of Fame Cisco Employee Hall of Fame Cisco Em...
Hello I am trying to migrate 6 VPN Tunnels from a Cisco 3900 router to a Cisco ISR 4451 router .I have 3 AWS accounts 2 in UAT 2 in Preproduction and 2 in Production.I am only able to bring bring up the Production tunnels interfaces the other re...
Resolved! OSPF Routing question
Hi team,Can anyone confirm the answer for this question?My answers are below but need to be verified by someone. Router4#conf trouter ospf 0.0.0.2 area 0.0.0.1 virtual-link 10.1.2.1 255.255.255.0end Router3#conf trouter ospf 0.0.0.1area 0.0.0.1 virt...
I would like to route two addresses in range of ports 9000-9100In single port command looks like:ip nat inside source static tcp 192.168.1.1 9000 192.168.1.2 9000but i dont know how to enter range of ports?
| User | Count |
|---|---|
| 16 | |
| 9 | |
| 8 | |
| 6 | |
| 3 |
