I have a legacy network which has a router with a WAN port (out side interface) and anouther interface on the local network (inside interface) with no routing protocols such as EIGRP, or OSPF running on it. Note: All sites routers are setup the same ...
Forum Posts
Resolved! How to load balancing in BGP
Hi,I have some questions regarding BGP1.Can BGP perform load-balancing? If so how?2.What is AS-PATH attribute in BGP and does it come into picture while doing load balancing.?
Hi Guys, I'm suffering a problem that about PBR and VLAN Interface on the Catalyst C9300-24UX, Cisco IOS XE Software, Version 16.06.03. My question is, I created a route-map and access-list as my PBR configuration, and then applied on VLAN 1, but the...
Dear all, I would just like to quick confirm.So specific IOS-XE version on ISR4K, it can support for "ip nat enable" command on ISR4K interface configuration mode however I think NVI interface does not function because no link up so I think it still ...
Resolved! Unable to shift the traffic using EIGRP
Hi, Can anyone help me with this topology. (Topology attached) I want to shift the traffic using EIGRP protocol. My destination in 10.68.96.0/30 network. Currently the traffic is preferring from R5 via R3,R2 and R1. but i want to shift the traffic v...
Hi Guys, does anyone know the problem that after a migration of RP2 from 3.x to 16.x the SIP10 cards are no longer recognized?And yeah, I know that the SIP10 with 16.x are no longer supported, but the cards are not recognized anymore in other routers...
I am currently testing PFRv3 in lab environment.I have tried to make single HUB-MC with two other routers as MC-Borders. on the Spoke side Branch MC and Border are on the same router. However, the PFRv3 channels cannot go both to RX state:From DMVPN ...
Resolved! ME 3800X | Bridge Domain Limit
We have setup where we are using a bridge-domain interface to connect to different CPEs through our ME3800. The BDI is setup on say BDI3 and we receive on different ports with different encapsulations/vlans, then strip the incoming tags off and place...
Resolved! 3925 basic config
I am trying to get this thing to have internet from GE0/0 available in the LAN connected to GE0/2 and am probably missing something stupid. I am able to ping google from the router but not from a computer on the LAN. version 15.2service configservice...
Router>sh ipv6 ospf n Neighbor ID Pri State Dead Time Interface ID Interface172.16.10.5 1 FULL/DR 00:00:36 2 FastEthernet0/0 What does 'Interface ID' mean???
I have 2 Branches connecting to same BGP Network with rest of Branches and HQ, I would like have fail over between these 2 Branches which are also connected P2P over WiMax Link , If obe Branch 1 Wan Fails I would all Traffic to go using Branch 2 Wan ...
Resolved! BGP Backdoor MPLS
helloi have below scenarioP router includes : R1 , R2 , R3 , R4PE router includes : R5 , R55 , R12 , R13CE router includes : R6 , R7 , R10 , R112 GREEN circle indicates 2 prefixes suppose : 1.1.1.0/24 & 2.2.2.0/24we have MPLS core backbone but for t...
Resolved! QoS packet drops
We have a 3945 router which is connected to our Service Provider's MPLS Cloud. There is a 100Mb circuit being delivered via Ethernet and is terminated on the Gi0/0 interface. We have the interface configured for 100Mb/full duplex. There is also Q...
There are two Cisco Routers in a Remote Branch & Border Gateway Protocol is running on both the Router & their inside interfaces are connected to a LAN Layer 3 switch enabled with Hot Standby Router Protocol.both the Router's outside interfaces are ...
hi everybodyi have router 3925 with IOS version c3900-universalk9-mz.SPA.156-3.M4.binTechnology Package License Information for Module:'c3900' ------------------------------------------------------------------------ Technology Technology-package ...
