I have a RV340 and am pretty green when it comes to CISCO router. Here is the details of our set up:3 VLANs - VLAN2 = 172.16.99.1/24, VLAN3 = 172.16.66.1/24 and VLAN4 = 172.16.77.1/24WAN PORT = 192.168.77.254/24 (Static IP)Inter-Vlan Routing are ena...
Forum Posts
hello to allin a MPLS scenario i saw that in last line of configuration requirement it mentioned :for any simplify future changes,your configuration must not limited to any prefixes.the total requirement about MPLS backbone and some others branches w...
I am currently attempting to use a managed switch connected to an unmanaged switch in order to eliminate some traffic on my network. I have 6 devices connected to the unmanaged switch and only need to access one on my network, however, the devices o...
Hi, i have a problem with 2921 cisco router The problem with high cpu load, but it appears only when somebody from office is downloading something big (downloading or updating various game clients) command show processes cpu monitor interval | exc...
Hi AllCan anyone tell me how the Firewall/IPS works on the ISR when running the Viptela IOS? does it use the normal ZBFW and IOS IPS or is it completely different ?
Hi We have multiple offices even we have integrated with Active Directory Cisco Umbrella Identity is not showing up on the reports which means i am not able to figure out which system is infected with Malware Or Command Control. Need to know what is ...
Hello All,I am looking for a "EPA-Blank" module visio stencil to fill in BAY2 area on ASR1002-HX router that I'm diagraming. I checked visio stencil documents on Cisco, but it is not available. Does anyone have any suggestions or a link to where I ca...
Resolved! Think I've bricked an ISR 4331
Ok so the order of events. Had a task to re-configure a 4331, it had an existing config and an older ios. As is my usual practice I backed up the config to flash just in case, with a copy command, giving no file extension. I then fttp'd the latest re...
i configure snmp for my new ISR4221 as per normal to what i did for my other C1941 routers.but seems like for this new ISR router, the snmp graph for zabbix is not showis there any thing else i need to add snmp-server community snmpcommunity ROsnmp-...
Hi All, I intend to setup a HA network infrastructure using the following setup. Two separate links from branch office to core sites 1 and 2, Two separate links from site 1 and site 2 towards the internet, Two separate links between the sites 1 and ...
Dear all, I plan to use NX-OS N9k such as C93148GC-FXP and C93180YC-EX. (not ACI)I have a concern Processing order of traffic when using NAT Please look at follouwing URL.IOS NAT Order of Operation is Listed. [NAT Order of Operation]https://www.cisco...
Recently I face one issue when serial port/line protocol up and I was not able to ping my own my. I regenerated the case as below. R1--s1/1---------s1/1---R2R1: s1/1: 10.10.10.1/30R2: s1/1: 10.10.10.2/30R1#sh ip int brief | s 1/1Serial1/1 ...
Hey everyone I'm running into an issue with recursive routing and can't seem to figure out how to fix it. I have an IPSEC with GRE runnning OSPF. The tunnel comes up fine but OSPF is flapping. It appears that the route to the destination is via the t...
Hi I wants to use prefix-list with LE or GE "Brach Sites" but when I configure for example ip prefix-list branch1 seq 1 permit 10.45.0.0/23 le 24But iWAN only shows the traffic like UC and only works when I configure a specific LAN 10.45.1.0/24 Thank...
Hola Buenas a todosNecesito orientación en la implementación de una topología LA CUAL VA ADJUNTA COMO IMAGEN PARA QUE SE ENTIENDA MEJOR.En primer lugar tengo un Router "casero" que nos puso el proveedor (foto adjunta), luego de eso un Sw capa 3 catal...
