I have two edges connected to two switches and two routers running VRF lite. The both routers terminate an MPLS circuit and and internet circuit into separate VRFs. There are sub-interfaces for each VRF from the switches and routers towards my edges....
Forum Posts
Hi, The syslog or logging messages on my SDWAN router have a very small buffer. Are these messages, if not sent to a syslog server stored in the admin tech and go back a few days at all? If so, where are they stored?ThanksBrad
I have vmanage clustervmanage1 - 10.2.26.4vmanage2 - 10.2.26.5vmanage3 - 10.2.26.12Every day I get the error "application-server cannot be reached on vmanage with IP address: 10.2.26.4" or "application-server cannot be reached on vmanage with IP addr...
Is is possible to disable cdp from WAN (ethernet) interfaces from template?I didn't find the option.Regards and thanks
HelloCurrently we have an existing SDWAN setup with Viptela edges 100B at remote sites and Controllers hosted in AWS.We are about to onboard few more sites which already have C1111-4P cisco routers.My question can we upgrade the cisco C1111-4P to SD...
Resolved! SDWAN Certificate installation problem
If we use CiscoOps' deployment option, and vmanage and smart accounts are already synced, do we still need to install certificates for controller or edge devices? If so, do virtual Edge devices need to be treated differently from physical Edge device...
Resolved! How to renew Certificate Expire
Hi Experts, I would like to ask about renew certificate for controller.I am using Cisco Automated Certificate and controllers at Cloud of Cisco, Expired Date is early of 2025 year. So after 2 years, how can I renew this certificate , are there any do...
Hello. I'm running SD-WAN fabric on EVE-NG When I try to open vAnalytics on vManage, error occurs. How can I solve this problem ?
Hello everyone,I'm trying to work on a Sd wan lab, and I have installed the certificate on both v manage and v smart but I'm not able to do the same thing on v Bond even when I tried with the V shell then the Tftp -g -r PKI.ca 223.1.1.13 command I ge...
Hi there!So i recently got a new task regarding our new CISCO ISR4331 IOS-XE.My Router is built in a way that it has 2 interfaces,1. GigabitEthernet0/0/0 - WAN Interface which uses the global routing table.2. GigabitEthernet0 - (MGMT) LAN Interface w...
Hi there, I am looking to compose a policy to force ACL to line VTY on SDWAN routersvManager -> Policies -> Access Control List Policy -> Add IPv4 Device Access Policy -> Add ACL Sequence But when I apply it to the template:Device Templates -> Additi...
actually i am trying to upgrade the NEW ISR1100X-4G from Viptela 20.4.1 to IOS-XE version :isr1100be-universalk9.17.09.03a.SPA.bin but it stuck on vedge as I could not use the commands copy or dir or even using my usb this is the first time upgradin...
The topology diagram is as follows. Two Cedges at the DC site have TLOC-EXT, and two Cedges at the Spoke site have TLOC-EXT. The DC site is connected to two ISP links. Both ISP links are behind the firewall. Will there be asymmetric traffic problems ...
Resolved! VRRP state issue
Hello, I have an issue on my cEgde device that both of them are seeing the state as MASTER, below is the config, ==== CE1#sh run int Gi0/0/0.1Building configuration... Current configuration : 342 bytes!interface GigabitEthernet0/0/0.1encapsulation do...
Hello, I do not understand the benefits of TLOC Extension. I does not seem to provide any more redundancy compared to two routers connecting to two separate transports. It only creates more IPSec tunnels and complicates the configuration. Can anyone ...
