We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
Hi all, have an old SG200 here that was trying to get going for use in a small office. However, booting it up and connecting directly to my laptop, link lights turn off after about 10 seconds. It looks like it will connect, but then it disconnects sh...
Hello, I configured 3 VLAN on a SG350-28P : VLAN 1 (192.168.1.0 /24) +------------------------...
Hello Guys, Is there any service timestamps log datetime equivalent command for Cisco SG350X. Thank you very much in advance. Regards,
I've been trying to enable SNMP by following these steps: 1. Going to SNMP -> Communities, and setting up a new community.2. Going to Security -> TCP/UDP Services, checking Enable for SNMP Service, and clicking Apply. When I do this, the web UI stops...
My setup: two SG350X-24 in a native stack, (close to) latest firmware.Although "show env" in terminal (and in the web GUI) shows only "OK" for temperature readings, SNMP (via1.3.6.1.4.1.9.6.1.101.53.15.1.10.1 and 1.3.6.1.4.1.9.6.1.101.53.15.1.10.2)se...
I am using four SG300 52 ports switches and one SG300 24 port POE switch for around 150 clients. I have been observing the random reboot of all these switches at the same time from last 2 months. Three 52 port switches are up-linked at one 52 port sw...
Hi have 2 sg300 following config on both gig 10 if:!interface gigabitethernet10description Uplinkchannel-group 1 mode on!interface Port-channel1description Uplinkswitchport trunk allowed vlan add 2-3! when patchcable (2 Pairs, pin 12, 36) is connecte...
I'm looking to see if anybody has found any 5G SFPs that are compatible with the SG500 series switches. I'm looking to upgrade the link between my two but this distance between them precludes using the direct attach stack cables. As 5GBase-T SFPs a...
Hi I'm new to home networking, but the problem I have is that I have to LANs (192.168.1.x and 192.168.2.x) but I don't know how to bridge or route network traffic between them, so if I'm on one LAN I can reach the other. The router for my #1 LAN is a...
Resolved! SG350XG upgrade questions
I have a 2 unit SG350XG stack that is currently running 2.3.5.63 firmware. I have uploaded the 2.5.0.83 file but I noticed it has "signed" in the filename which the 2.3 does not. Can I jump to this newer, signed version with a simple file swap and ...
Hi I'm not sure how to configure a new VLAN on my Cisco SG300-10 switch. I want to create a new VLAN (192.168.2.x) for AV and Security devices on port 2 of my switch. I can find directions for creating the VLAN, but what I can't tell is if I need to ...
Hi,I have a SG350-10 which suddenly started acting up one day to the next (at least i am not aware what I changed while it was still running).Its my office switch so it gets powered up and down a lot, while the other ones I have (including another 35...
I have a new SG250-18 as my new lab core switch. All is well but one port for my access point. Single flat /24 (172.16.30.x) and all is well. This switch has a 2 port LAG over to it's 8 port counter part (SG200-8) to get to the my network edge dev...
Team, Working with a Global Customer who utilizes the SG110-08HP all over the world. We just ran into an issue in Taiwan that the products aren't able to be imported there by an integrator in another APAC country? Guess the question is - can w...
Hi, How many devices we can support simultaneously in Smart Network Application (SNA)? Regards!
