Switches - Small Business - Page 40

Looking for support docs and videos? Check here

We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...

Helpful support links - Updated September 2023 w/ Catalyst 1200 - 1300

(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...

Resolved! Password reset

i have C2950-C3H2S-M someone was set to enable passwords i want to reset is please suggest.

Cisco CBS250-8T-D and default language

Hi My switch is set to english, but if I havent logged it to it for a couple of days, sometime just a few hours, the loginscreen is Japanese or chinese, i then have to choose english again. Is this normal, is there a way to choose English as default ...

Resolved! Cisco switch vs Windows NPS: Invalid credentials

We've just bought a new Cisco switch for our office: CBS220-48T-4G. Full disclaimer - aside from setting up a VLAN once in the past, I'm pretty new to switching in general, let alone Cisco switches specifically.I know that this switch offers 802.1x w...

Guest SSID communication with DHCP over CISCO SG350-28

Hello,We are using Cisco SG350-28 Model Network Switches, with these switches our APs (non-CISCO Make) are connected. These APs have on OS base Controller software which is installed on Windows computers. 1) Each AP has Two SSID, One is for Company U...

cisco sg350 power problem

I have a Snom phone connected to SG350 PO. Have configured POE per prot limiting and it does not work.On LLDP the phone does not get IP from DHCP server.IT shows also invalid signature counter on POE port settings

Resolved! Cisco Switch Model Required

Minimum 3 switch models required which fulfill the mentioned requirements which are:- 48 x 1Gb connections with the capability to tag each port to its own VLAN and trunk the VLANS through the switches to the ESXi server.

IpV4 Routing on SG300-10

Hi allMy first time posting on here so I'm hope you all have patience with me thanks in advance.What I have done through the web GUI is set up two vlans, vlan2 and vlan3 with different ip's with dchp pool. They work fine, and there is no communicatio...

Is secondary IP supported on SG-300?

I want to have devices with IP addresses from 2 different subnets allowed on the same VLAN and use the VLAN interface IP as the default gateway for thode devices.With a L3 Catalyst switch, I would just add a secondary IP address to the VLAN interface...

Cisco SG 500 Series - Firware Issue

Hi, Just suddenly 5 of our switches got crashed by themselves. it started to reboot and could not find the image file. the system light is blinking and no interface is working at all. Is there any kind of bug and suddenly the image's time is over? I ...

SG250-08HP Boot Loop

Hi,I have a brand new SG250-08HP that was working fine for the last week and then ive gone to power it on and now its stuck in a boot loop where the startup config will load and then 10 seconds later all the ports shutdown and then the unit reboots a...

Resolved! Multicast

Please help ,multicast or IPtv will work for below setup ? i have huawei access switch model s5735 connected to cisco core switch 3850 series via huawei sfps. Cisco core 3850Vlan 65 IPTVip multicast auto-enableInterface Vlan 65ip address 192.168.65...

Resolved! SG300 Ignore Fan Failure Restrictions

SG300-28 with resistor managed half-speed fans. Works perfectly except won't allow SFP adapters to function. Two other SG300s with same mod work as they should. I need both half-speed fans and fiber adapter connection. This is another thread buildi...

Resolved! Two SG300 Switches, LC-LC fiber and 1320nm Adapters

I am pretty certain that this has worked in the past but I'm am needing to go to fiber (instead of copper) for a long run at an entertainment venue. Ports 27 and 28 on the SG300-28 switches are trunked as is port 10 on the SG300-10, 2x VLANs on all s...

monitor port on SRW2008MP

is there a monitor port configurable on this switch?Is there later FW than 1.0.4? I have boot ver 1.0.1 h/w version 00.03.00Where can I get the latest FW for this switch ?

Resolved! What is the difference between an SF300 and an SG300?

I tried to find out on the web but found no comparisons. Thanks. D.

Switches - Small Business

Forum Posts

Looking for support docs and videos? Check here

Helpful support links - Updated September 2023 w/ Catalyst 1200 - 1300

Resolved! Password reset

Cisco CBS250-8T-D and default language

Resolved! Cisco switch vs Windows NPS: Invalid credentials

Guest SSID communication with DHCP over CISCO SG350-28

cisco sg350 power problem

Resolved! Cisco Switch Model Required

IpV4 Routing on SG300-10

Is secondary IP supported on SG-300?

Cisco SG 500 Series - Firware Issue

SG250-08HP Boot Loop

Resolved! Multicast

Resolved! SG300 Ignore Fan Failure Restrictions

Resolved! Two SG300 Switches, LC-LC fiber and 1320nm Adapters

monitor port on SRW2008MP

Resolved! What is the difference between an SF300 and an SG300?

Congratulations to the Event Top Contributors Class of 2024!

Cisco + Splunk: It's a new day for your data.

A new chapter of the Spotlight Award begins!

Join us in Celebrating the New Year and the Nov.-Jan. Winners!

Announcing Resources That Guide You to Success

Cisco Business Product Family

Cisco Switching Product Family

Difficult to find MIB CPU utilisation Switch - model CBS250-8T-D

CBS350 renew wildcard SSL certificate

sg500 DHCP pool limit

Which series of Cisco switch 24 port PoE+ for Arbua AP 635

is it possible to restore sg300-28 config on a sg300-28PP Switch