We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
Resolved! SG350 - Issue Routing Between VLANs
Hi All, I am a beginner here and looking for some help with intervlan routing using an SG320-10. I updated the switch to the latest firmware (2.5.5.47) and started with default configuration. I followed Cisco's video here (I only changed the vlan n...
После замены старого TP-Link на Cisco SF110-24 у части устройств подключенных к нему, пропал доступ в интернет. При этом у большинства пользователей подключенных через этот коммутатор проблем не наблюдается. Сетевая карта получает от DHCP сервера дан...
Resolved! VLAN on daisy chained cisco SG350-20
Hello,I'm struggeling here... So! Here is how it works : I have 6 cisco SG350-20 switches daisy-chained. On the fourth of the line I have interpretation system that needs to send data on receivers connected to the other switches (1 receiver per switc...
Hi,I hope that someone can assist me with this cause I'm starting to feel like a real nube! My SF300-24 switch has been working 100% as a backup switch for a client of mine. At my clients premises it was running 3 Vlan's and doing inter VLAN routing....
Hello friends, I have a problem with a sg200-50 switch, I will summarize how you got to this problem. Estava estudando a operação e as funções do interruptor, quando decidi atualizar o firmware, realizei o procedimento e tudo aparentemente correu bem...
I have an issue I am unable to understand and resolve. I recently installed an SG350X-48P Gigabit switch. We have several VLANs on the switch and we can access the internet via the Default Gateway, but only when the PC is configured for DHCP. If the ...
Hello,We've just implemented one Cisco SG500-28 on our infrastucture. I need to monitor this Switch, but the switch doesn't matchs with Cisco Catalyst switchs mibs.I downloaded the SG500 mib (here) , but don't find OIDs for CPU utilization and enviro...
I am trying to link two cisco SG112-24-NA switches via a 10GB copper SFP. Is there anything I need to do to configure them
Hi all, I am facing one issue on the Cisco Small Business SG Switch Model (SG350X-24MP-K9-UK) that the port on TenGigabitEthernet1/0/3 still remain UP even had unplugged the cable. Tried to swap SFP, fiber uplink, upgrade firmware, reboot switch but...
Is there a way to enable the Bridge-MIB on an SG220 to be able to view dot1dTpFdbTable ? I am trying to query that table to map switch ports to mac addresses.
Hi,I need to update the firmware for my linksys rv042 dual wan router. Please help.
Resolved! SG250-08 loses all users on reboot
I have recently acquired a SG250-08 switch and this switch is losing all users every time it reboots (both graceful reboots and power failure reboots). Is this the expected behaviour for this equipment and I need to configure it somehow or have I bou...
Hello,I am hoping someone can help point me in the right direction here, I am looking for quite a basic setup. We have just purchased 6 x SG-350 and I am having trouble working out if my config is right. I am used to Catalyst IOS and these switches h...
Greetings!I'm a Cisco noob with a couple SG350-10s, ciscored and ciscoorange (cisco orange is a 10P) and I sure could use some advise. I moved to the Ciscos from a couple of netgears that were just awful, and what a wonderful upgrade!! :) Trouble ...
Hi,I installed a Cisco SG350XG-24T in a customer's network. Some 10 GB capable devices work fine (Synology, Mac mini and an iMac Pro). But when I connect a brand new iMac (10 GB capable) to the network from one of the offices it won't get a connectio...
