Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...
Forum Posts
Dear, I'm trying to create a lacp port channel between a Nexus and ASR 903Everything work well using a " switchport mode access" while by using the portchannel as Trunk the Portchannel goes down and the interfaces related to it went to suspended stat...
My teacher told me that there would be a feature that would make the Fastethernet ports on the switch into gigabitethernet ports?Is there any such feature?And if so what is that feature called?
Hi All, I've got a pretty simple question probably for most of you. We are changing some equipment and the VLAN / Static Routes are different, most of them are really bad so we are trying to clean them up. we haveSite AVLAN1 10.27.0.0/24 at Site A1 ...
Resolved! Cisco C9300P-48 PoE Question
I have a stack of 4 C9300P-48 switches. I have them power stacked also. The switches available power differs between them. My question is why? Below is the "show power inline" output. Module Available Used Remaining (Watts) (W...
Rehabbing a Cisco 3560 Switch for a new project.Performed a password recovery, reloaded defaults and updated the IOS to the current version. Now I have a "bell" noise about every 10 seconds. Anyone have any ideas on how to turn off? Manny
Hi We are planning to purchase some C9300 with a DNA center and everything with the DNA Advantage subscription. I'm not understand if I need a an additional Smartnet contract or not. According to this document I'm getting with the DNA Advantage subsc...
Switch model is C9200L-24P-4G-E V01 The customer wants to use the web interface to configure a simple access port with a voice vlan for their IP phones. Let's sayinterface gig1/0/1switchport mode accessswitchport access vlan 10switchport voice vlan 2...
getting unrecognised characters while taking the console. tried changing speed but no hope..
hi ...trying to get mpls l2 xconnect up between cisco and juniper router but unable to do so. local interface: Gi0/0/0.100 up, line protocol up, Eth VLAN 100 up Interworking type is Ethernet Destination address: 2.2.2.2, VC ID: 100, VC status: down...
Hello all,I have already configured a Master Key with the command: key config-key password-encryptWhen I tried to configure cts on an interface, I am not able to insert a type 6 password:int Te1/0/1 cts manual no propagate sgt sap pmk 6 KIv...
Got a strange problem, maybe some of you could help.Dhcp snooping is up and running, database are saved to tftp file, all looks good. Snooping running on one vlan, switch#show ip dhcp snooSwitch DHCP snooping is enabledSwitch DHCP gleaning is disable...
Hi all, i run ios 15.2 version and have a problem to receive on my snmp monitor the interface vlan accounting information.Is there any command that i must configure on global or interface vlan base? Thanks!
Resolved! how do you stop show tech
How do you stop show tech COMMAND from displaying all the input w/out stoping.. I need to captur something there but it goes fast all the way to the end.. Thanks
Hi everyone, I'm configuring per-vlan policing on 3850 switch like below : class-map VLAN10 match vlan 10 policy-map POLICING_VLAN class VLAN10 police cir 5000000 conformed-action transmit exceed-action drop interface Gi1/0/48 switchport...
My name is ali. I am new in Cisco. Now a days i am studying Cisco Switching by myself. When i watched some videos then i feel some confusions. therefore i need a expert who help me. I will pay him weekly. When i feel confusion i will make a document ...
