Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, February 2, 2026, through Friday, February 20, 2026. Our colleagues Amruta Navadagi, Anaya Kalawat, and Mohammad Mehtabuddin will be waiting to assist you...
Hello,I own a Cisco 2950 and I want to download the new firmware on it using TFTP,So I tried the "copy tftp://192.168.10.11/c2950-i6k2l2q4-mz.121-22.EA13.bin flash:", but when the result is this :Here are the TFTPD logs:Connection received from 192.1...
Folks, I am having a hard time understanding some concepts I am reading about for Enterprise campus network design, more specifically the switch block design. On page 19 of the new SWITCH 300-115 Official Cert Guide details Figure 1-14, and shows t...
I have configured Cisco 1841 router for the ILL connectivity, but when I try to ping gateway or Google shows RTO.Internet connection shows No Internet access, My ISP IP 40.248.253.50 and Local IP is 192.168.0.1and the gateway is 40.248.253.49 I have...
Hi, Is there any way to connect to a CISCO ASA 5506-X VPN from mobile without any licence? Only the default licence is on, no other licence. I read that on mobile the VPN only work if i buy a licence (AnyConnect licence ). Best Regards,Peter
Hello, I need to convert 2* 4500X from standalone to VSS, in a network production, and during business hours. I didn't found any documentation, but I found the 6500 one, so I will use it and adapt. But I have one question : If I begin to convert firs...
Hi I have the following strange situation. Topology is 10 24 Port 2960 X switches attached to one 2960 x switch. The infrastructure is used for Guest Wireless only . So we have one Firewall 1 WLC and 50 AP doing the job. 2 of the 10 Switches are in s...
One C2960X switch from the switch stack is stuck in a loop The switches were running c2960x-universalk9-mz.150-2.EX5.bin we was attempting to upgrade to c2960x-universalk9-mz.150-2.EX5.bin. All other switches upgraded to that version without an issu...
Hello, I am stuck and don't know how to solve this issue when I try to ping my other PC on the other network I get the following message Destination host unreachable. Router 1interface GigabitEthernet0/0ip address 192.168.72.49 255.255.255.248duplex...
Hello, Im new to cisco packet tracer, and I have a one question. Why does not my server give out DHCP adresses to the different networks and what should I do to make it work?On the router i have: /Greg
Hi Guys.!!I have an incident that for Thin Client LAN port not came up . When we connect through IP phone its working unless its doesn't up.Can you guide me to sort out this issue..
Hello all Bit new at this, but I've successfully installed and configured a an ASA 5525x to get the WS on my inside interface to connect to the internet, as well as allow outside access to several servers inside my network. Now, however, I'm running ...
Hello, I'm stacking 6 switches this weekend but switch 1 and 6 are far apart so that I can't close the loop with the 50 cm stacking cable. Would the stack still come up as normal until we order a long enough stacking cable? Thanks
Hello. I'm trying to setup a Port-Channel (or EtherChannel) between my ASR 1000f Router and 3570X Switch.I need to pass VLANs 10,20,30 & 40 over the Port-Channel (This is why I set the Switch ports as Trunks) Need to confirm if this is the correct ap...
Hello,I've configured NAT, but it is not working.Could you tell me what is wrong with my configuration? -------------------------------------------------------------------------! !upgrade fpd autoversion 12.4service timestamps debug datetime msecserv...
I have a 4 Cisco 3750X stacked showing a high CPU utilization and I would like help to find the root cause: I found the HRPC qos request process with high utilization. CPU utilization for five seconds: 95%/1%; one minute: 92%; five minutes: 81%PID ...
