Hey Fellows!I'm not gonna lie but the Cisco Documentation of LDAP is quite bad and not useful. (And I'm still only in NX-OS I don't think catalyst is better)I have successfully set an Authentication using this site:https://ccierants.blogspot.com/2013...
Forum Posts
We currently use FlexLink in our systems. However, we recently found out that newer switch hardware will not support FlexLink, so we are exploring the use of FlexLink+. In a test environment, with FlexLink+ configured, we see momentary comm loss on o...
Hello everyone..I want to add more 1 segment in 1 VLAN because it is to differentiate users on different floors.For example :for VLAN 100, there are 2 segments IP or 2 IP address for gateway , they are..192.168.101.1192.168.102.1 (as secondary IP or...
Resolved! IOS upgrade on WS-C2950-24 running SI
I have 2 WS-C2950-24 switches which are using the Standard image IOS release(c2950-i6q4l2-mz.121-22.EA2.bin).I need to enable layer 3 QOS on these switches, is it possible to upgrade to the Enhanced Image IOS (12.1.22-EA9(ED),or do I need to replace ...
Hi, thereI've a couple of WS-C4507R+E switches (Version 03.08.07.E.152-4.E7) with installed standby supervisor engine.After attaching to the standby supervisor engine ("attach module 4", "session module 4") I'm getting cli authorization fails if I tr...
Resolved! Silent reload C3850
I am building a new network to run in parallel during the transition to new building addition.I have purchased two WS-C3850-48XS, however due to strict budget I purchased them refurbished and no SmartnetI deployed them in StackWsie Vrtual.Over the la...
Hi, I need IOS ipbasek9 for WS-C2950-24 is there anyone know how can i get those ios. because i search in cisco download for WS-C2950-24 is not available. Thanks, Rocky
Resolved! IOS for WS-C2950-24
Hi all Is there anyone who would be able to help me to download the below IOS version from Cisco? I only need the link as I do have authorization to download IOS s. Product : WS-C2950-24 Required IOS : c2950-i6k2l2q4-mz.121-22.EA14.bin Thanks Beh...
Dear Experts,I Need IOS for support both the command Switchport block musticast and Switchport block unicast in cisco WS-C2950-24So which IOS i have to upgrade to support both the above mention command. in cisco 2950-24 switch.Thanks in ADV,Vaib...
Hi All,I have a cisco C2950 and I've just did a firmware upgrade. I have downloaded the c2950-i6q4l2-tar.121-22.EA14.tar and I've installed the firmware accordingly. Everything went well, the Switch is booting with new version etc..etc..The problem I...
Resolved! Etherchannel Port state=Down Not-in-Bndl
I have a problem with the interface in Etherchannel.The Etherchannel is set up between stacked 4x2960 and 4x3750 switches.The link has two ports on each side, but only one is active.2960:Group Port-channel Protocol Ports------+-------------+---------...
Hi, does C9300 Network Module NM-8x support 1G SFP? Based on datasheet, NM-8X is for 10G spf. Can anyone please advise whether it supports 1G SFP? Thanks in advance.
Hi team,We have an ongoing issue with our customer connected CCT bundle, and it is showing packet drops. We were able to isolate the issue to a single point and the issue is between Provider Edge switch to Cat 4500 cluster. We have connected a test r...
This is on a 4500X running 03.08.06.EThere doesn't seem to be a cookie option under the deny statements in an extended ip access-list. ip access-list extended FOO switch01(config-ext-nacl)#permit ip any object-group BLOCKED log ? WORD User d...
Hi.I am not a network expert, so it is possible that I don't use the correct terminology... Sorry for that.I am having a very weird issue with some of my devices (access control door control units) connected to a core switch, they get randomly discon...
